Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not change the plug in any way. 36. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. Page 3 FEATURES Your sander is suitable for sanding with coarse, medium, and fine grit sandpaper. It will produce a fine scratch free finish when used to sand with the grain on wood surfaces. It has been designed so that flush corner sanding on three sides of the sander is possible. Your sander has a comfortable palm grip handle that provides maximum one-hand control and comfort, plus it reduces operator fatique during continuous sanding operations. Your sander has quick action paper clamps. This makes changing or replacing sandpaper fast and easy. Your sander also has a built in dust collection that collects dust through punched holes in the sandpaper and cushion. See Figure 1. Before attempting to use your sander, familiarize yourself with all operating features and safety requirements. SWITCH This tool is equipped with a simple switch control. To turn your sander "ON", depress the switch button as shown in Figure 1. Depress the switch button in the opposite direction to turn your sander "OFF". ELECTRICAL CONNECTION Your sander has a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A voltage drop of more than 10 percent will cause a loss of power and overheating. If your tool does not operate when plugged into an outlet, double-check the power supply. WARNING: IF ANY PARTS ARE MISSING DO NOT OPERATE YOUR SANDER UNTIL THE MISSING PARTS ARE REPLACED. FAILURE TO DO SO COULD RESULT IN POSSIBLE SERIOUS PERSONAL INJURY. WARNING: DO NOT ALLOW FAMILIARITY WITH YOUR SANDER TO MAKE YOU CARELESS. REMEMBER THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT TO INFLICT SEVERE INJURY. PAPER PUNCH Fig. 1TABLEVER CUSHION SWITCH ON OFF SWITCH PAPER CLAMP PLATEN DUST BAG The operation of any sander can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI Z87.1. WARNING: Page 4 Page 5 OPERATION WARNING: YOUR SANDER SHOULD NEVER BE CONNECTED TO POWER SUPPLY WHEN YOU ARE ASSEMBLING PARTS, MAKING ADJUSTMENTS, ASSEMBLING OR REPLACING SANDPAPER, CLEANING, OR WHEN NOT IN USE. DISCONNECTING SANDER WILL PREVENT ACCIDENTAL STARTING THAT COULD CAUSE SERIOUS PERSONAL INJURY. INSTALLING NON-ADHESIVE SANDPAPER See Figure 2. Inspect sandpaper before installing. DO NOT use if broken or defective. 1. Unplug your sander. WARNING: FAILURE TO UNPLUG YOUR SANDER COULD RESULT IN ACCIDENTAL STARTING CAUSING POSSIBLE SERIOUS PERSONAL INJURY. 2. If replacing sandpaper, remove old sandpaper. To remove paper, release paper clamp by lifting up on lever and disengaging it from the tab on the platen. 3. Insert end of new 1/4 sheet sandpaper approximately 1/2 in. (13 mm) under the paper clamp. Note: 1/2 in. (13 mm) clamping of sandpaper is necessary for multi-sheet stacking of paper. 4. Lift up on lever and lock into place. Apply downward pressure to conform sandpaper to platen. 5. Wrap sandpaper around cushion. Lift lever on opposite end of sander and insert loose end of sandpaper under paper clamp. Fit sandpaper tight against cushion. 6. Lift up on lever and lock into place. 7. Multiple sheets of sandpaper can be installed at one time for convenience. INSTALLING ADHESIVE SANDPAPER See Figure 2. Inspect sandpaper before installing. DO NOT use broken or defective sandpaper. 1. Unplug your sander. WARNING: FAILURE TO UNPLUG YOUR SANDER COULD RESULT IN ACCIDENTAL STARTING CAUSING POSSIBLE SERIOUS PERSONAL INJURY. 2. If replacing sandpaper, remove old sandpaper by peeling it off cushion. If removing regular sandpaper, release paper clamp by lifting up on lever and disengaging it from the tab on the platen. 3. Remove non-adhesive sandpaper, then lift up on paper clamp lever and lock it into place. 4. Care...