Se requieren dos o más personas para levantarla. CÓMO COLOCAR LAS RUEDAS 1. Invierta la base (A) (Fig 1). 2. Alinee los orificios del conjunto de las ruedas (B) con los de las placas de la base. Coloque una arandela plana pequeña de 8 mm (5/16") sobre un tornillo de cabeza hexagonal de 8 mm x 19,1 mm (5/16" x 3/4"). Coloque el tornillo a través del orificio en el conjunto de la rueda y enrósquelo en el orificio de la base. Coloque los conjuntos de la otra rueda de la misma forma. 3. Ajuste

Main Street 714-641-0529 Fax: 714-641-2947 Santa Barbara 93101 Buena Tool Co. 433 Laguna Street 805-963-3885 Santa Rosa 95401 Acme Electric Tool Repair 742 Wilson Street 707-546-5862 Santa Rosa 95403 H & V Tool Repair 1808 Empire Industrial Court #D 707-528-1111 Simi Valley 93065 Simi Tool Repair 1236 Los Angeles Avenue, UnHD 805-584-8138 Temecula 92390-5623 California Electric Service 41715 Enterprise Circle North 909-695-5445 Torrence 90502 Universal Tool Service 21804 S. Vermo

22 Fig. 23 OPERATING CONTROLS & ADJUSTMENTS WARNING: FOR OPERATOR SAFETY, MAKE CERTAIN THE DUST INTAKE PORT IS COVERED WITH THE VACUUM HOSE BEFORE OPERATING THE MACHINE. THE ROTATING FAN INSIDE THE BLOWER HOUSING IS ACCESSIBLE THROUGH THE DUST INTAKE PORT AND IS HAZARDOUS. MAKE SURE INTAKE CAP COVERS THE INTAKE PORT WHEN HOSE IS REMOVED. ALWAYS WEAR PROPER APPAREL.DO NOT WEAR JEWELRY, AND KEEP FINGERS AND ALL FOREIGN OBJECTS OUT OF THE DUST INTAKE PORT.ALWAYS FOLLOW THE SAFETY RULES OF THIS MANU

12A 4. Inserte la varilla (A) Fig. 12B en el orificio del soporte (B). Asegurese de que ninguno de los cuatro extremos de la bolsa este doblado. 5. Coloque el extremo abierto de la bolsa de filtro dentro de la ranura superior del tambor del recolector de polvo hasta que quede seguro y sellado. (De manera similar a como se inserto el anillo interior de la bolsa inferior, Fig. 9. Sera necesario doblar y plegar el anillo interior de retencion para bolsa a fin de que calce en su lugar. 6. La Fig. 12

Indica una situación potencialmente riesgosa, que si no es evitada, podría resultar en la muerte o APELIGRO: A ADVERTENCIA: lesiones serias. APRECAUCIÓN: Indica una situación potencialmente peligrosa, la cual, si no es evitada, podría resultar en lesiones menores o mode-radas. PRECAUCION I Usado sin el símbolo de seguridad de alerta indica una situa-ción potencialmente riesgosa la que, si no es evitada, podría causar daños en la propiedad. PROPOSICIÓN DE CALIFORNIA 65 fiTJ M Algunos tip

In a severe dirty operation, the blower impeller should be cleaned with a wire brush to prevent an accumulation of foreign matter that could result in blower unbalance After cleaning impeller, inspect for possible cracks or excessive wear, which can cause unbalance. DO NOT USE AN IMPELLER THAT IS CRACKED OR EXCESSIVELY WORN; REPLACE IT WITH A NEW IMPELLER. MOTOR MAINTENANCE: Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. shou

The smaller the gauge number, the heavier the cord. 15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury. 16. FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed. 17. DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result. 18. DON’T OVERREACH. Lo

4. Thread hex nut (B) Fig. 4 onto each of the four bolts and tighten securely. ASSEMBLING SIDE SUPPORTS 1. Place the dust collector base (A) Fig. 5, in an upright position as shown. 2. Align the two holes in the bottom of side support (B) Fig. 5 with the two holes (A) in the base. 3. Insert a 5/16-18x3/4" hex head screw (A) Fig. 6 thru each hole in the side support and base. 4. Place a 5/16" lockwasher onto the hex head screw. 5. Thread a 5/16" hex nut onto the hex head screw and tighten securel

14A, with the two holes in the drum. Insert a 1/4-20x5/8" hex head screw through the holes in the retaining clip and the holes in the drum. Place a 1/4" flat washer onto the screws, and thread 1/4-20 hex nut s on the screws and tighten securely. Repeat this process for the three remaining sides of the drum. A B Fig. 14A A B C Fig. 15 ASSEMBLING DUST INTAKE PORT AND CAPS TO BLOWER AND MOTOR ASSEMBLY 1. MAKE CERTAIN THE DUST COLLECTOR IS DISCONNECTED FROM THE POWER SOURCE. 2. Align the four holes

Cutters 09-128 & 09-137 are counterbored to fit Stub Spindle. Cutters are shown 3/8 size. 1/2 Lb. each. 09-100 09-101 09-102 09-103 09-106 1/2" Cove 5/16" Cove 1/8" & 3/8" 1/4" & 1/2" 90° 5/16" Qr. Rd. 3/8" Bead Qr. Rd. Qr. Rd. V-Groove 1/4" Bead 09-109 09-111 09-112 09-113 09-114 1/4" Flute Stile with Rail with Drop Leaf Drop Leave 1/4" Groove 1/4" Tongue Bead Cove 09-115 09-116 09-117 09-118 3-Bead Clover 1/2" Rad. 3/4" Qr. Rd. Cove Leaf Base Shoe 09-120 09-121 09-125 09-126 09-128 Ogee Female