Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Warning: The caller display will not work without batteries installed. 2. Installation 2. Plug the coiled handset cord into the Handset. Plug the other end into the jack on the left side of the Base unit. 3. Place the Handset in the Base unit. Always use the telephone line cord supplied with your Lyris 410 phone. Other telephone line cords may not work. IMPORTANT - Before removing the battery compartment cover,always make sure the base unit is disconnected from the telephone line. ■ Install 2 pcs of Alkaline AAA batteries into the battery compartment and place back the cover before use. Note: 1) Please do NOT use Rechargeable batteries in this phone. 2) Battery is not included the unit 3)The battery life is typically about 6 months, depending on usage. When the battery is low, CH will show up of the display screen. If you do not replace the batteries, they will become totally discharged and your display screen will not work. and you may lose all the telephone memories and settings. BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two screws (supplied with the unit) at the marked locations, l eaving approximately 7mm between the wall and the the screw head. Hang the cradle unit on the screws using the wall mount slots. You may need to remove the telephone from the wall and tighten the screws so that the cradle is securely fixed and does not wobble. Place the Handset on the cradle with the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset. 3. Desk/^Vall mount installation 4. Setting up your phone Desk Mount To place the Lyris 410 on a desk, connect the stand to the bottom of the phone in the slots near the rear of the base as shown below. Insert the rigid clips of the stand into the slots on the bottom of the phone (near the rear of the base). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward (3) as shown below. Wall Mount 1. Locating the Base unit The Base unit should be placed on a level surface, in a position where: ■ the telephone line cable will reach your telephone line socket or extension socket. ■ it is not close to a sink, bath or shower, or anywhere else where it might get wet. ■ it is not close to other electrical equipment - fridges, washing machines, microwave ovens, TVs, fluorescent lights, etc. To place the Lyris 410 on a wall, connect the stand to the bottom of the phone in the slots near the front of the base cover as shown below. Desk/^Vall mounting continue... Insert the rigid clips of the stand into the slots on the bottom of the phone (near the front of the base). Press down firmly until the flexible clips clicks into place. To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below. 4. Plug the telephone line cord free end intoa modular wall jack. Press the cable into the groove so that the Base unit stands level. 5. Lift the Handset and check for Dial tone in the earpiece. Mark two points on the wall that are 92 mm apart to lay the fixing centers as shown below. Press the SET/STO button to enter the menu and then use U P or DOWN b uttons to cycle through the following options: ■ SET 1 DATE ■ SET 2 LCD ■ SET 3 FLASH Note: The system will time out if you leave more than 8 seconds between key presses. You will need to set the correct time and date so they can be displayed correctly on the display. If you subscribe to a Caller Display service, the time and date will be set automatically on receipt of your first incoming call. In standby mode, press SET/STO button. o The display shows ' SET 1 DATE '. Press SET/STO button to confirm. o The 'year' icon will be blinking. Press UP or DOWN button to set the year. Press SET/STO button to confirm. o The 'month' icon will be blinking. Press UP or DOWN button to set the month. Press SET/STO button to confirm. o The 'date' icon will be blinking. Press UP or DOWN button to set the date. Press SET/STO button to confirm. o The 'hour' icon will be blinking. Press UP or DOWN button to set the hour. Press SET/STO button to confirm. o The 'minute' icon will be blinking. Press UP or DOWN button to set the minute. Press SET/STO button to confirm the setting. o The display shows ' SET 2 LCD ' , you can continue with programming,or press DELETE button to return to standby mode. In standby mode, press SET/STO button. o The display shows ' SET 1 DATE '. Press UP or DOWN button until the displayshows 'SET 2 LCD'. Press SET/STO to confirm. Press UP or DOWN button to select your comfortable display viewing level (1~8).The default setting is 3. Press SET/STO button to confirm the setting. o The display shows ' SET 2 LCD ' , you can continue with programming, or press DELETE button to return to standby mode. Set Time/Date 1 2 3 "© 4 (''"...