Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
- 56041684 - BA 755, BA 855 - B-9 B-10 / ENGLISH INSTALLING THE BRUSHES (DISC SYSTEM) M CAUTION! Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels. 1 Make sure the Brush Deck (7) is in the RAISED position. Make sure the Key Switch (A) is off (O). 2 If using pads, install the pads on the pad holders. 3 See Figure 2. To mount the Brushes (AA) (or pad holders) align the Lugs (BB) on the brush with the holes on the mounting plate and turn to lock in place (turn the outside edge of brush towards the rear of machine as shown (CC)). B-10 - FORM NO. - 56041684 - BA 755, BA 855 ENGLISH / B-11 INSTALL THE BRUSHES (CYLINDRICAL SYSTEM) M CAUTION! Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels. 1 Make sure the Brush Deck is in the RAISED position. Make sure the Key Switch (A) is off (O). 2 See Figure 3. To access the brushes loosen the black knobs (one on each side) on top of the idler assemblies (29) and remove the idler assemblies. Slide the brush into the housing, lift slightly, push and turn until it seats. Re-install the idler assemblies. FORM NO. - 56041684 - BA 755, BA 855 - B-11 B-12 / ENGLISH FILLING THE SOLUTION TANK Fill the solution tank with a maximum of 113.5 Liters (30 gallons) of cleaning solution. Do not fill the solution tank above 7.5 cm (3 inches) from the bottom of the Solution Fill (1). The solution should be a mixture of water and the proper cleaning chemical for the job. Always follow the dilution instructions on the chemical container label. NOTE: EDS machines can either be used conventionally with detergent mixed in the tank or the EDS detergent dispensing system can be used. When using the EDS detergent dispensing do not mix detergent in the tank, plain water should be used. A CAUTION! Use only low-foaming, non-flammable liquid detergents intended for machine application. Water temperature should not exceed 54.4 degrees celsius (130 degrees fahrenheit) SQUEEGEE INSTALLATION 1 See Figure 4. Slide the Squeegee Assembly (13) onto the squeegee mount bracket and tighten the Squeegee Mount Thumb Nuts (25). 2 Connect the Recovery Hose (19) to the squeegee inlet. 3 Lower the squeegee, move the machine ahead slightly and adjust the squeegee tilt using the Squeegee Adjustment Knob (26) so that the rear squeegee blade touches the floor evenly across its entire width and is bent over slightly as shown. B-12 - FORM NO. - 56041684 - BA 755, BA 855 ENGLISH / B-13 DETERGENT (EDS) SYSTEM PREPARATION AND USE COMMON INSTRUCTIONS: The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over floor drain before purging because a small amount of detergent will be dispensed in the process. To Purge When Changing Chemicals: 1 Disconnect and remove the detergent cartridge. 2 Turn the Key Switch (A) ON and press the Detergent Switch (F) and the Solution Switch (B) down for at least 2 seconds. NOTE: Once activated the purge process takes 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system. To Purge Weekly: 1 Disconnect and remove the detergent cartridge. Install and connect a Cartridge filled with clean water 2 Turn the Key Switch (A) ON and press the Detergent Switch (F) and the Solution Switch (B) down for at least 2 seconds. NOTE: Once activated the purge process takes 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system. When the Detergent Cartridge is almost empty a Display Panel (D) indicator will come on. This “Low Detergent’ indicator will remain on until you reset the system. Once this indicator comes on you should be able to simply pour an entire gallon bottle of detergent into the Cartridge to refill without worrying about measuring. NOTE: Only reset the system when the cartridge is full. When switching cartridges, the “Low Detergent’ indicator is only accurate if the replacement cartridge is at the same level as the cartridge being replaced. To Reset: 1 Turn the Key Switch (A) ON and hold the Detergent Switch (F) down for 2 seconds. See illustration on next page for Detergent System indicators. NON-REFILLABLE CARTRIDGE SPECIFIC INSTRUCTIONS: Remove the Cap (AA) and place the cartridge in the detergent box. Install the Dry Break Cap (BB) as shown. REFILLABLE CARTRIDGE SPECIFIC INSTRUCTIONS: Fill the detergent cartridge with a maximum of 4.73 Liters (1.25 gallons) of detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to filling to avoid spilling detergent on the machine. It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the detergent name on each cartridge to avoid mixing them up. The...
Otros modelos de este manual:Aspiradoras - 56315043(755C) (4.84 mb)
Aspiradoras - 56315042(755) (4.84 mb)
Aspiradoras - 56315045(755 EDS) (4.84 mb)
Aspiradoras - 56315046(755C EDS) (4.84 mb)