Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
3) Burning objects such as cigarette butts. 4) Bulky objects such as vinyl, paper etc. 5) Sharp objects such as needles, pins, metal, glass particles etc. 4. Attachments ..Nozzle : for cleaning wooden floor, the room floor and carpet. ..Crevice Tool : for cleaning any crevice, inside corners or window frames. However, do not use the crevice tool more than 20 minutes because it may cause harm to the motor. ..Dusting brush : for cleaning clothes curtains. 5. Close supervision is necessary when this vacuum cleaner is used by or near children. Childrenis carelessness may cause damage to the cleaner or injure persons. 6. Air exhausted from the vacuum cleaner is normally warm. But if extraordinarily hot air is exhausted, check if the telescopic tube, hose or clean filter is clogged or not. 7. Electric shock could occur if used outdoors or on wet surfaces. CAUTIONS BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE VACUUM CLEANER, DISCONNECT THE ELECTRICAL POWER SUPPLY CORD FROM THE WALL OUTLET. 1. Motor exchange 1) Separate the Body Cover and Body Base by unfastening the screws. 2) After disconnecting the lead wires, replace the old motor with a new one. 2. In case of exchanging other parts. refer to the exploded view. -4- DESCRIPTION Hose Assembly, Flexible Pipe Assembly, Telescopic Cord Reel Button Power Cord Dust Tank SPECIFICATIONS • MODEL : REFER TO THE COVER PAGE • POWER SOURCE : ON RATING PLATE • POWER CONSUMPTION : ON RATING PLATE • POWER CONTROL : - MAIN : SLIDE KNOB CONTROL (F/HOSE) • CORD LENGTH : 6 m • HOSE LENGTH : 1.8 m • NET WEIGHT : 4.65 kg • PACKING WEIGHT : 7.5 kg • NET DIMENSION : 402.259.275 (D.W.H) • PACKING DIMENSION : 575.290.330 (D.W.H) • ATTACHMENTS HOSE ASSEMBLY,FLEXIBLE..........................................1EA PIPE ASSEMBLY,TELESCOPIC .....................................1EA NOZZLE ASSEMBLY, FLOOR.........................................1EA BRUSH ASSEMBLY, DUST .............................................1EA NOZZLE,CREVICE............................................................1EA BRUSH ASSEMBLY,DUST(depending on model)..........1EA • This specifications are subject to change according to the buyer's request. Nozzle Assembly,Floor BRUSH ASSEMBLY, DUST (depending on model) NOZZLE,CREVICE -5- Methods for Disassembly, Assembly and Repair of Main Parts Need-to-know for disassembly . Pull out the plug before disassembly and adjustment. 1. All the parts are almost connected by screws or assembled by insertion. Disassemble in order with reference to the disassembly diagram. 2. Do not proceed with further disassembly except the necessary part. Parts beyond the disassembly diagram are not to be disassembled. Method for disassembly of main parts 1. Method for disassembling the cover of the main unit. 1) Press the locker on the handle carrier of main unit. Then grasp the tank’s handle to pull tank assembly from the body of main unit. 2) Remove pre-filter assembly from the main unit. 3) Remove the back pieces including cover of exhaust filter and exhaust filter. 4) Loosen the screws in the base of the main unit (with TPL4x20:4 pieces, .. type drive) 5) Loosen the screw in the body cover of the main unit (with TPL4x20:2 pieces, .. type drive) Cover of exhaust filter Exhaust filter Button on exhaust filter -6- 6) Lift the cover assembly of the main unit. 2. Method for disassembling code reel / Case assembly 1) Loosen the screw fixing the Chamber. (with TPL 4x20:2 pieces , .. type drive) 2) Lift the Case assembly. 3) Lift the code reel assembly 3. Replacement of motor 1) Disassemble the motor assembly as shown in the figure (with TPL4*16:4 pieces, .. type drive) 2) For re-assembly after disassembling the motor cover, do so in the reverse sequence and insert the packing seal, motor and mount packing. During the assembly, make sure to prevent the packing seal and motor mount packing from dropping out (which may reduce the suction force). Cover, Motor Damper, Motor Mount Motor Packing seal Chamber PCB TROUBLE SHOOTING GUIDE 1. SWITCH ON BUT MOTOR DOSE NOT TURN. CHECKING CAUSE SOLUTION Poor plug insertion Insert again Power cord cut Repair or exchange CHECK THE POWER SOURCE Interior lead wire cut Exchange the lead wire Motor(stator armature) coil cut Exchange the motor or damaged 2. SWITCH ON, MOTOR DOES NOT TURN BUT BUZZES. Motor armature cut Exchange the motor Ball bearing defacement Exchange the motor Impeller hindrance Remove the foreign matters. (Caused by foreign matters) -7 3. SWITCH OFF BUT MOTOR TURNS 4. WEAK SUCTION POWER Low rotation speed Poor connection Motor armature cut Foreign matters attached to the impeller Low voltage Repair. Exchange the motor Remove the foreign matters Inquire to the power utility company Hose and extension wands Remove the foreign matters are clogged with foreign in the hose or extension matters. wands. Motor turns normally, but suction power is weak. Air filter...
Otros modelos de este manual:Aspiradoras - VK8810HUV (2.37 mb)