This allows you to program eachtransmitter to more than one vehicle in two car families and also allows youto change which button or buttons control certain functions of the system. (Example: Transmitter channel 5, shown below, can be programmed toactivate Receiver channel 2.) Refer to the chart below for access to each ofthe transmitter channels, and for the standard factory button assignments. TRANSMITTER SYSTEM RECEIVER CHANNEL BUTTONS CHANNEL FUNCTION 1 1 Remote Arm * Remote Emergency Panic*

Rev. A - Change Power station to charging stand pg. 3. 9-16-98 Rev. B - Change battery type from ni-cad to rechargeable pg. 3,4 9-16-98 Rev. C - Change Warranty and Customer Service telephone number 4-25-00 Model FR-214 CTCSS Privacy Code System active ON AIR Transmit mode active BUSY Signal being received BAT LOW Low battery voltage warning SCAN Channel Scan in progress CH Current channel LOCK Tranciever settings locked 1 128-5379C 2 of 12 Powering the transceiver: Your FR-214 radio transceiver

Although this transmitter can be programmed into any of the Audiovox remote start and or alarm, remote start systems, it will offer limited use and should be used for the remote start upgrade only. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position 2) Press and release the programming switch 3 times 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes indicating the transmitter ha

This transmitter can be used with any Audiovox unit color coded with an Orange LED in the receiver. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position. 2) Press and release the programming switch 3 times. 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes indicating the transmitter has been learned. 4) Repeat step 3 for each transmitter up to a total of 4. Turn the ignition of

Although this transmitter can be programmed into any of the Audiovox remote start and/or alarm, remote start systems, it will offer limited use and should be used for the remote start upgrade only. To program this transmitter into your remote start upgrade unit: 1) Turn the ignition to the on position. 2) Press and release the programming switch 3 times. 3) Press and hold, for 3 seconds, the button of the transmitter you wish to add until the parking light flashes, indicating the transmitter

If this condition persists after corrective action, consult your dealer or experienced installation facility. 3. By adhering to these warnings and safety considerations, serious accidents and/or personal injury can be avoided. 128-6814 3 of 8 Contents SIR-HK1 Installation/Wiring Precautions Install Manual Audio Cable P/N 1286814 (P/N 112B3293) 1. Make sure the adapter cable is not connected to an AC wall outlet until all interconnections have been made and verified. The adapter power cable shoul

• Avoid extremes in exposure to water, heat, and cold. This transceiver is weather resistant but not waterproof. • Do not expose the transceiver to long periods of direct sunlight, nor place the transceiver close to heating appliances. • Do not place the transceiver in excessively dusty areas, humid areas, wet areas, nor on unstable surfaces. • If smoke or something unusual is coming from the transceiver, immediately switch OFF the power and remove the batteries from the transceiver. Contact you

PROGRAMMING TRANSMITTERS: NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds ofthe previous step. If the 15 second time limit expires betweensteps, the unit will automatically exit the program mode. Thisis indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm thetransmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, the v

Lock and arm/unlock and disarm. May be programmed to unlock driver's door or all doors. Also will initiate and terminate *Panic. Pulsed or switched output to control Remote Trunk Release or optional device connected to channel 3. When pressed and release two times, will provide pulsed output or activate the Remote Start option when installed. When so equipped, this button can be used to operate an optional device connected to channel 4. When so equipped, this button can be used to operate an opt

Some of the FR-1428 features are: No Air Time Fees and No License Required Up to 2 Mile Range Auto Battery Saver and Auto Squelch 14 Channel, 38 CTCSS Multifunction LCD Display Continuous Tone Coded Squelch System (CTCSS) Talk Confirmation Tone and Call / Ring Button Interchangeable Faceplates -3 PERFORMANCE Your transceiver will achieve its maximum operating range when communicating with other transceivers in a flat open area with no trees or buildings obstructing its signal. Range may be up to