Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
10, 12) TONE Button (p. 22) PROGRAM Button (p. 10, 18) ВАТТ (Battery) LOW Indicator (p. 9) Antenna * * * AUTO Button (p. 10, 18) INTERCOM Indicator (p. 20) INTERCOM Button (p. 20) FLASH Button (p. 12, 22) LOUD/RINGER Button (p. 12, 13) REDIAL7PAUSE Button (p. 12, 22) CH (Channel) Button (p. 12) Charge Contacts (p. 9) 6 Base unit Antenna {p. 3, 8) LOCATOR/INTERCOM Button (p. 20) IN USE/CHARGE Indicator {p. 9) VOLUME Buttons (p. 15) Handset Hook {p. 25) TONE Button (p. 22) Charge Contacts {p. 9) RINGER Selector (p. 16) SP-PHONE (Speakerphone) Button and Indicator (p. 14) HOLD Button (p. 15) MIC (Microphone) (p. 14, 20) FLASH Button (p. 14, 22) REDIAL Button (p. 15) PAUSE Button (p. 22) 7 Connection Fasten the cord to prevent it from being disconnected. Single-Line Telephone Jack (RJ11C) Telephone Line Cord Power Outlet (AC 120 V, 60 Hz) AC Adaptor N. о USE ONLY Panasonic AC ADAPTOR KX-A11. о The AC adaptor must remain connected at all times. (It may feel warm during use. This is normal.) о If you connect a standard telephone on the same line, see page 11. 8 cí> Battery Charge Place the handset on the base unit for about 3 hours before initial use. «> The IN USE/CHARGE indicator lights. Indicator Recharge When the BATT LOW indicator flashes or the unit beeps intermittently, recharge the battery. ® The BATT LOW indicator will continue to flash for at least 10 minutes once you begin recharging. This time will increase the more you use the handset while recharging. Standard battery life If your Panasonic battery is fully charged; OOO BATT LOW Indicator While in use (TALK) Up to about 8 hours While not in use (Stand-By) Up to about 30 days o Battery life may vary depending on usage conditions and ambient temperature. o Clean the handset and the base unit charge contacts with a soft dry cloth once a month or once a week if the unit is subject to grease, dust or high humidity. If not, the battery may not charge properly, o Once the battery is fully charged, you do not have to place the handset on the base unit until the BATT LOW indicator flashes. This will maximize the battery life. © The battery cannot be overcharged. 9 Settings Selecting tlhe Dialling Motile You can program the dialing mode by using the handset near the base unit. When your telephone line has touch tone service, set to TONE. If rotary service is used, set to PULSE. The factory preset is TONE. The TALK and SP-PHONE indicator lights must be off before programming. Press I PROGRAM I. «»The TALK indicator flashes. Press I auto I. 3To select PULSE, press © twice. OR To select TONE, press (*) twice. When finished, press i PROGRAM!, o A confirmation tone sounds.* 006 Ooo o°o 000 Qjjy -TALK Indicator -I AUTO I PROGRAM o To cancel programming, press I PROGRAM I. then restart from the beginning, o If 3 beeps sound during programming, you have pressed a wrong key. Restart from step 1. *What the confirmation tone means 1 beep: The mode is different from a previously selected one. 2 beeps: The mode is the same as a previously selected one. If a power failure occurs, the mode will return to the factory preset (TONE). Reprogram if necessary. 10 CoBwemBooft Desk Usage The wall mounting adaptor can also be used to raise the unit at an angle. (3) Insert the tabs of the wall mounting adaptor into the “DESK” openings in the unit. 0 Push the adaptor in the direction of the arrow, o “UP DESK” should face upward. о It is necessary to pull down the handset hook (p. 7). Adding Another Phone This unit will not function during a power failure. To connect a standard telephone on the same line, use a Panasonic T-adaptor KX-J66. 11 Eiaknog/AimswOTmig CaDDs Making Calls with the Handset -j Press 1 TALK i. o The indicator lights. 2 Dial a telephone number. o If you misdial, press I FLASH I firmly then dial again. Q To hang up, press I TALK I or place the handset on the base unit. o The TALK indicator light goes out. ITALK land Indicator FLASH I loud/ringer! [REDIAL/PAUSE I EH] ° If an alarm tone sounds in step 1, move toward the base unit or place the handset on the base unit. Then try again, o To switch to the speakerphone during a call with the handset, see page 17. To redial the last number Press I TALK I Ei> I REDIAL/PAUSE I. To select the receiver volume LOW, MEDIUM (preset) or HIGH Press I LOUD/RINGER I while talking. o Each time you press the button, the volume level will change. (MEDIUM O HIGH LOW C> MEDIUM c> • • •) If noise interferes with the conversation Press |CH I to select a clear channel or move closer to the base unit. 12 Answering Calls with the Handset If the handset is off the base unit, press I TALK 1. © You can also answer a call by pressing a dialing button 0 to 9, *, or # {—Any key Talk). OR If on the base unit, just lift it up. Adjusting the ringer volume Be sure the TALK indicator light is off. © To select HIGH (preset) or LOW, press I...