Votos - 1, Puntuación media: 3 ( )

Fabricar: Alpine Tamaño del archivo: 1.56 mb Nombre del archivo: OM_MRX-F30_V60_EN_FR_ES.pdf Idioma del manual:

Conecte el cable de la bateria proveniente del amplificador directamente al terminal positivo (+) de la bateria del vehiculo con el fusible en linea adecuado del vehiculo (consulte la seccion Cable de la bateria). No conecte este cable al bloque de fusibles del vehiculo. Para evitar que entre ruido externo en el sistema de audio. Coloque la unidad y pase los cables a 10 cm (3-15/16”) por lo menos del conjunto de cables del automovil. Mantenga los conductores de alimentacion de la bateria lo mas alejados posible de otros cables. Conecte el conductor de puesta a tierra con seguridad a un punto metalico desnudo (si es necesario, elimine le pintura o la grasa) del chasis del automovil. Si anade un supresor de ruido opcional, conectelo lo mas lejos posible de la unidad. Su proveedor Alpine dispone de varios supresores de ruido. Solicitele mas informacion. Su proveedor Alpine conoce la mejor forma de evitar el ruido. Solicitele mas informacion. • • • • • Fig. 3 MRX-V60 MRX-F30 (Left Side/Cote gauche/ Lado izquierdo) (Left Side/Cote gauche/ Lado izquierdo) (Right Side/ Cote droit/ Lado derecho) (Right Side/ Cote droit/ Lado derecho) a g h i j k f b c d e a b c d e l m n o p g h i j k f l m n o p q q r * Be sure to add an in-line fuse with the battery lead as close as possible to the battery’s positive (+) terminal./Veillez a ajouter un fusible en ligne au fil de la batterie aussi pres que possible de la borne positive (+) de la batterie./No olvide anadir un fusible en linea con el cable de la bateria tan cerca como sea posible del terminal positivo (+) de la bateria. English Francais Espanol aSpeaker Output Terminals The MRX-V60/MRX-F30 has two screw terminals for each speaker output. Be sure to observe correct speaker output connections and polarity in relation to the other speakers in the system. Connect the positive output to the positive speaker terminal and the negative to negative. Do not connect the speaker (-) terminal to the vehicle’s chassis. In the bridged mode, connect the left positive to the positive terminal on the speaker and the right negative to the negative terminal of the speaker. Do not use the speaker (–) terminals as a common lead between the left and right channels. Do not connect this lead to the vehicle’s chassis. NOTES: 1. Do not connect speaker leads together or to chassis ground. 2. Use a Y-adaptor (sold separately) for the input when bridging the outputs. (Refer to the “Bridged Connections” on page 14) bFuse • MRX-V60 ..................... 30A x2 • MRX-F30 ..................... 25A x2 USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES. Failure to do so may result in fire or electric shock. cPower Supply Terminal dBattery Lead (Sold Separately) Be sure to add an in-line fuse with the battery lead as close as possible to the battery’s positive (+) terminal. This fuse will protect your vehicle’s electrical system in case of a short circuit. Consult the table below for appropriate fuse value and minimum wire gauge requirement. MRX-V60 ........................ 60 amp fuse, 4AWG/21mm2 MRX-F30 ......................... 50 amp fuse, 8AWG/8mm2 eRemote Turn-On Lead (Sold Separately) Connect this lead to the remote turn-on (positive trigger, (+) 12V only) lead of your head unit. If a remote turn-on lead is not available, see Connection Checklist section on page 10 for alternative method. Note: If using speaker input level signal from the head unit, remote turn-on lead connection is not necessary due to automatic signal detection. fGround Lead (Sold Separately) Connect this lead securely to a clean, bare metal spot on the vehicle’s chassis. Verify this point to be a true ground by checking for continuity between that point and the negative (–) terminal of the vehicle’s battery. Ground all your audio components to the same point on the chassis to prevent ground loops while keeping wire length as short as possible. Minimum required wire gauge for this connection is as follows: MRX-V60 .............................4AWG/21mm2 MRX-F30 ..............................8AWG/8mm2 aBornes de sortie de haut-parleur Le MRX-V60/MRX-F30 possede deux bornes a vis pour chaque sortie du haut-parleur. Veillez a effectuer correctement les raccordements aux bornes de sortie correspondantes et a respecter les polarites par rapport aux autres haut-parleurs du systeme. Raccordez la borne de sortie positive a la borne positive du haut-parleur, et la borne negative a la borne negative. Ne raccordez pas la borne negative du haut-parleur (-) au chassis du vehicule. En mode ponte, connecter la sortie positive gauche sur la borne positive du haut-parleur et la sortie negative droite sur la borne negative du haut-parleur. Ne pas utiliser les bornes haut-parleur (–) a la fois pour les canaux droit et gauche. Ne pas connecter ce cable sur le chassis du vehicule. REMARQUES : 1. Jamais connecter les conducteurs de hautparleur ensemble ou sur la terre du chassis. 2. Pour l’entree, utiliser un adaptateur en forme de Y (vendu separeme...

Descargar ahora

Introduzca dos números de la imagen: