Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Move the cursor to this line, and press the ‹/› Buttons until OFF appears, disabling the Auto Poll feature. With Auto Poll turned off, the receiver will only check for a signal at the audio input assigned to the source. DMP SETTING: If you select DMP/The Bridge as your source input, you will notice that the AUDIO IN line of the INPUT SETUP menu has been replaced by the option GO TO DMP SETTING. See Figure 48. Figure 48 – Input Setup Menu Screen for DMP/The Bridge source Since The Bridge is connected to the AVR using a dedicated audio connection, it isn’t possible to select a different audio input for this source. However, there are several special settings used only with The Bridge. Selecting GO TO DMP SETTING displays the DMP SETTING menu (see Figure 49). Figure 49 – DMP Setting Menu Screen MODE: The first line of the DMP SETTING menu allows you to select whether the iPod will be used to listen to music (or other audio materials), or view a video or still image, if your iPod is video- or photo-capable. INITIAL SETUP REPEAT: Set REPEAT to ONE, ALL or OFF to repeat one track, all tracks in an album or playlist, or not to repeat any tracks. SHUFFLE: Set SHUFFLE to SONGS to play all songs on the iPod in random order. The ALBUMS setting plays all albums in random order, with each album’s tracks played in album order. RESUME: Set RESUME to ON to resume playback of a track from the point where it was interrupted by turning off the AVR, switching sources on the AVR, or removing the iPod from The Bridge. Set RESUME to OFF if you wish to restart play from the beginning of the track after interruptions. NOTE: The Resume setting disables the Remember Playback Position setting that you may set for audio and video files using later versions of iTunes. Resume affects all files on the iPod until you manually change the setting either in the DMP SETTING menu or by using iTunes. CHARGE IN ST-BY: Your iPod’s battery may be charged while it is docked in The Bridge with the AVR turned on. Set CHARGE IN ST-BY to ON to enable charging even when the AVR is in Standby mode (but not completely off). When CHARGE IN ST-BY is set to OFF, the iPod will charge only when the AVR is turned on. NOTE: In order to access the DMP SETTING menu, press the AVR Selector on the remote so that it operates the AVR 146. You may then press the OSD Button and use the Navigation and Set Buttons, as usual, with the on-screen menu system. When you are ready to return to operation of your iPod using the remote, remember to press the DMP/The Bridge Selector so that the transport and other controls operate The Bridge. To simplify use, you may wish to program two macros on your remote, one to select the AVR and issue the commands within the OSD system to display the DMP SETTING menu, and a second macro to remove the menu from the display and return the remote to operation of The Bridge. See the Macros section of the Advanced Functions section of the manual for more information on programming macros. The remaining lines in the Input Setup menu activate the tone controls, and may be skipped at this time. We recommend leaving the tone controls at their factory defaults for most listening, in order to enjoy the sound mix created by your favorite movie and music artists. However, if your room or speakers have unusual characteristics, or simply as a matter of personal preference, see the Tone Controls section on page 35 for more information. You are now ready to begin enjoying your new receiver! 33 OPERATION Now that you have installed your system components and completed at least a basic configuration of your receiver, you are ready to begin enjoying your home theater system. Turning On the AVR 146 Gently press the Master Power Switch until the word OFF is no longer visible. The Power Indicator above the two power switches should light up in amber. This indicates that the AVR is in Standby mode and is ready to be turned on. Normally, you may leave the Master Power Switch in the ON position, even when the receiver is not being used. See Figure 50. Figure 50 – Power Switches There are several ways in which the AVR 146 may be turned on: a) Press the Standby/On Switch on the front panel. See Figure 50. b) Press the Source Select Button on the front panel. See Figure 51. Figure 51 – Source Select Button/The Bridge c) Using the remote, press any one of these buttons: AVR, DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, AM/FM or 6CH. See Figure 52. Figure 52 – AVR and Input Selectors NOTE: Any time you press one of the remote’s Input Selectors (i.e., DVD/CD, TAPE/The Bridge, HDMI 1/HDMI 2, VID1, VID2, VID3, AM/FM or 6CH), the remote will switch modes so that it will only transmit the codes programmed to operate that device. To control the receiver, press the AVR Button to return the remote to AVR mode. To turn the receiver off, press either the Standby/On Switch on the front panel, or press the AVR Button and the OFF Button on the remote. Unless the receiver wi...