Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
6 - 7 Input Wiring Diagram........................................................ 8 Output Wiring Diagram..................................................... 9 Operation.................................................................. 10 - 12 Warranty...........................................................................13 HIGH PERFORMANCE STEREO AMPLIFIER This power amplifier has been designed to provide high Quality performance with a minimum of maintenance. However, it's performance will only be as good as the care HELP! and quality of components with which it is installed. We therefore advise that you 1-800-645-4994 read these instructions very carefully to familiarize yourself with the product and it's features. Monday-Friday 8:30am - 7:00pm EasternShould you require assistance with the installation or wiring so this unit, please call Saturday 9:00am - 5:00pm Easternour toll-free "HELP" line at 1-800-645-4994 during the days/hours shown. SPECIFICATIONS Maximum Output Power: 500 Watts 125 Watts RMS x 2 @ 4 Ohms Output Impedance: 2 - 8 Ohms (stereo) Frequency Response: 10 - 35KHz +/-1 dB Channel Separation: 60 dB Signal / Noise Ratio: 90 dB Input Impedance: Low-Level 10K Ohms High-Level 100 Ohms Input Sensitivity: Low-Level 200 mV - 8 V. High-Level 2V - 10 V Filter type: Selectable High/Full/Low-pass Crossover @12 dB / Octave Filter Crossover: LPF 50-250 Hz (variable) HPF 50-250 Hz (variable) Supply Voltage: 12 volts, negative ground Fuse Rating: 15 amps. Dimensions (W X H X D): 295 mm X 54.3 mm X 228.6 mm 11-5/8" X 2-1/8" X 9” * Due to continuing improvement, Audiovox reserves the right to change features and design without notice. -3 PRECAUTIONS 1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive(+ ++) terminal of the battery. Connect this wire only after having completed and checked all other connections to the amplifier. 3. By nature of its design, a power amplifier generates heat and requires good air circulation around it to dissipate that heat. Do not install the amplifier in an enclosed area which does not permit adequate air circulation. Should the temperature of the unit rise too high, the internal thermal sensors will shut off operation until it has cooled down sufficiently. 4. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully check all electrical connections to the unit. 5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery and chassis ground must be of a thick enough gauge to provide this voltage to the amplifier. We recommend #10 gauge wire or thicker (smaller gauge #) for the battery and ground leads. 6. Make certain that the speaker(s) to be used with this amplifier are capable of handing the output power (wattage) of the unit. Use of speaker(s) not rated for the output of this amplifier may cause damage to or failure of the speaker(s) for which Audiovox will not be liable. -4 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustration. 3. Remove the amplifier and drill a 1/8" hole at each of the four locations. CAUTION: Before drilling the holes, look at the underside of the mounting surface. Always check carefully to avoid drilling into wiring, braces, fuel or brake lines. CHECK BEFORE YOU DRILL! 4. Secure the amplifier to the mounting surface using The self-tapping screws provided. -5- INSTALLATION INSTRUCTIONS INSTALLATION DIAGRAM WIRING INSTRUCTIONS The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to the appropriate diagrams for the system configuration you are using. The power and speakers wire connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw for the connection to be made and fully insert the wire (strip 1/2" of insulation from the end) under the respective screw on the side panel (crimp-on "U" terminals are provided to simplify wiring and we recommend their use.). Tighten the screw down to secure the wire. 1. Power Connection The battery terminal (BATT) must be connected directly to the positive terminal of the vehicle battery to provide an adequate voltage source and minimize noise. C...