Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
If you didn’t connect surround speakers choose NO (the sound of the surround channels is sent to the other speakers). • SB – Select the number of surround back speakers you have (one, two or none). Select LARGE if your surround back speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn’t 1 connect surround back speakers choose NO. • SUB W. – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected (see notes below). Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you want deeper bass (the bass frequencies that would normally come out the front and center speakers are also routed to the subwoofer). If you did not connect a subwoofer choose NO (the bass frequencies are output from other speakers). 3 When you’re finished, press RETURN. You return to the Manual SP Setup menu. Tip • If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in the amount of bass due to low frequency cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results, listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers. Crossover Network • Default setting: 80Hz This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or the subwoofer, and bass sounds playing back from those selected as SMALL. It also decides where the cutoff will be for bass sounds in the LFE channel.2 1 Select ‘Crossover Network’ from the Manual SP Setup menu. 4.Manual SP Setup :Return a.Speaker Setting b.Crossover Network c.Channel Level d.Speaker Distance e.THX Audio Setting f.THX Speaker Setup 4b.Crossover Network :Finish Frequency 80Hz ( THX : 80Hz ) 2 Choose the frequency cutoff point. Frequencies below the cutoff point will be sent to the subwoofer (or LARGE speakers). 3 When you’re finished, press RETURN. You return to the Manual SP Setup menu. Channel Level Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system. 1 Select ‘Channel Level’ from the Manual SP Setup menu. 4.Manual SP Setup :Return a.Speaker Setting b.Crossover Network c.Channel Level d.Speaker Distance e.THX Audio Setting f.THX Speaker Setup 4c.Channel Level Test Tone Manual :CancelENTER:Next 2 Select a setup option. • Manual – Move the test tone manually from speaker to speaker and adjust individual channel levels. • Auto – Adjust channel levels as the test tone moves from speaker to speaker automatically. Note 1• If the surround speakers are set to NO, the surround back speakers will automatically be set to NO. • If you selected Second Zone or Front Bi-Amp (in Surround back speaker setting on page 33) you can’t adjust the surround back settings. • If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal. 2• For more on selecting the speaker sizes, see Speaker Setting above. • If you’re using a THX speaker setup, confirm that the crossover frequency is set to 80Hz. En The System Setup menu The System Setup menu 3 Confirm your selected setup option. The test tones will start after you press ENTER. 4c.Channel Level Test Tone [ Manual ] Please Wait . . . 20 Caution! Loud test tones will be output. :Cancel 4 Adjust the level of each channel using /. If you selected Manual, use / to switch speakers. The Auto setup will output test tones in the order shown on- screen: 4c.Channel Level L 0.0dB C [ 0.0dB ] R [ 0.0dB ] SR [ 0.0dB ] SBR [ 0.0dB ] SBL [ 0.0dB ] SL [ 0.0dB ] SW [ 0.0dB ] :Finish Adjust the level of each speaker as the test tone is emitted.1 5 When you’re finished, press RETURN. You return to the Manual SP Setup menu. Tip • You can change the channel levels at any time by using EFFECT/CH SEL and +/– on the remote control. You can set two channel levels: one for MULTI CH IN and one for the listening modes. Speaker Distance For good sound depth and separation from your system, you need to specify the distance of your speakers from the listening position. The receiver can then add the proper delay needed for effective surround sound. 1 Select ‘Speaker Distance’ from the Manual SP Setup menu. 4.Manual SP Setup :Return a.Speaker Setting b.Crossover Network c.Channel Level d.Speaker Distance e.THX Audio Setting f.THX Speaker Setup 4d.Speaker Distance L 10.0ft (Reference) R [ 9.0ft ] C 9.5ft SL [ 6.0ft ] SR [ 6.5ft ] SBL [ 6.0ft ] SBR [ ...
Otros modelos de este manual:El receptor y el amplificador - VSX-80TXV (2.25 mb)