2 Press EQ. 3 Press the cursor buttons ( or ) to select “PRESET CLEAR”. 4 Turn the jog dial to select “YES”, then press ENTER. “Are you sure?” appears in the display. 5 Turn the jog dial to select “YES”, then press ENTER. The adjusted contents of the selected equalizer bank are cleared. For advanced EQ menu adjustments Use the CUSTOMIZE menu and set “MENU EXPAND” to “ON” to enable advanced adjustments. For details on “MENU EXPAND”, see page 47. For details on how to set the items, see page 55. 46 GB Advanced settings Using the CUSTOMIZE menu to adjust the receiver You can adjust various receiver settings using the CUSTOMIZE menu. 1 Press CUSTOMIZE. The CUSTOMIZE button lights up and “<<>>” appears in the display. 2 Press the cursor buttons ( or ) to select the parameter. For details, see “CUSTOMIZE menu parameters” below. 3 Turn the jog dial to adjust the selected parameter. 4 Repeat steps 2 and 3 to adjust the other items. CUSTOMIZE menu parameters The initial setting is underlined. x MENU EXPAND (Menu expanding) •ON The advanced parameters for the SET UP, SURROUND, LEVEL, and EQ menus are displayed and can be adjusted. For details on each setup items, see pages 19, 43–45 and the following pages. • OFF The advanced parameters are not displayed. x dts 96/24DEC. (DTS 96/24 decoding mode) • AUTO When a DTS 96/24 signal is input, it is played back at 96 kHz sampling frequencies. • OFF Even when a DTS 96/24 signal is input, it is played back at 48 kHz sampling frequencies. Note This parameter is valid only in the AUTO DECODING mode (page 34). In other sound fields, this parameter is always set to “OFF”. x 2CH MODE (2 channel decoding mode) You can use the NORMAL SURR (;PLII/NEO:6) button to set the 2 channel decoding mode (page 38). You can set this parameter only when NORMAL SURROUND or AUTO DECODING* is selected. In the Cinema Studio EX mode, this parameter is always set to “PRO LOGIC” and cannot be changed. For details on each decoding mode, see page 38. * The selected decoding mode is applied only when the Dolby Digital [Lt/Rt] signal is input. • PRO LOGIC • PLII MOVIE • PLII MUSIC • Neo: Cinema • Neo: Music x SB DECODING (Surround back decoding mode) You can use the CUSTOMIZE menu to set the surround back decoding mode (page 39). For details on each decoding mode, see page 39. • AUTO • MATRIX • OFF x MULTI CH 1 (Multi channel 1 assignment) x MULTI CH 2 (Multi channel 2 assignment) Initial setting: NONE (no assignment) Lets you assign the audio signal input to MULTI CHANNEL IN 1 (or 2) jacks to any function except TUNER and PHONO. You cannot assign both “MULTI CH 1” and “MULTI CH 2” to the same function. x D.POWER (Digital power management) • AUTO OFF Lets you turn off the power of the unnecessary digital circuits automatically when outputting the analog audio signals using the ANALOG DIRECT or MULTI CH DIRECT function. You can enjoy high quality analog audio without the influence of digital circuits. • ALWAYS ON Lets you keep the power of digital circuits on. Select if you do not like the time lag that occurs with the “AUTO OFF” setting when digital circuits are turned on, etc. continued Advanced Adjustments and Settings 47GB Advanced settings (continued) x AUTO FUNCTION (Control A1: Function link) • ON x V.POWER (Video power management) • AUTO OFF Lets you turn off the power of the unnecessary video circuits automatically. You can enjoy high quality audio without the influence of video circuits. • ALWAYS ON Lets you keep the power of video circuits on. Depending on the monitor, noise may be produced or the picture may be distorted when the power of the video circuits is turned on. In this case, select “ALWAYS ON”. x S.FIELD LINK (Sound field link) • ON Lets you apply the last selected sound field to a function whenever it is selected. For example, if you select STADIUM for CD/SACD function, change to a different function and return to CD/ SACD function, STADIUM is automatically applied again. • OFF Sound field link is not activated. x DECODE FORMAT (Digital audio input decoding mode) Lets you specify the input mode for the digital signal input to the DIGITAL IN jacks. • AUTO Automatically switches the input mode between DTS, Dolby Digital, PCM, or MPEG2. • PCM Decodes all the input signals as PCM signals. If a Dolby Digital, DTS, or MPEG (etc.) signal is input, no sound is output. When set to “AUTO”, and the sound from the digital audio jacks (for CD, etc.) is interrupted when playback starts, set to “PCM”. Lets you switch the function of this receiver to the Sony components connected via CONTROL A1 cords (page 60) automatically when the playback on the component is started. • OFF Function link is not activated. x 2 WAY REMOTE (2 way remote control system) • ON Lets you turn on the 2 way remote control system. Normally, select “ON”. • OFF Lets you turn off the 2 way remote control system. When you use another receiver, etc. that is also compatible with the 2 way remote control system, together ...
)
