Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Kenwood Tamaño del archivo: 1.27 mb Nombre del archivo: Idioma del manual:

1 Select SP SETUP and press the SET UP key again so that the subwoofer setting indication “SUBW ON” appears. 2 Use the MULTI CONTROL knob or keys to select the appropriate subwoofer setting. 1 SUBW ON : Subwoofer setting mode to the receiver is ON. 2 SUBW OFF : Subwoofer setting mode to the receiver is OFF. • The initial setting is “SUBW ON”. • When the setting “SUBW OFF” is selected, the front speakers are automatically set to “FRNT LRG” and the procedure skips to step 6. Before step 6, press the SET UP key to accept the setting. • When subwoofer output sound is required, select “FRNT NML”. 3 Press the SET UP key to accept the setting. • The front speakers setting indication “FRNT LRG” appears. 4 Use the MULTI CONTROL knob or keys to select the appropriate front speakers setting. 1 FRNT NML (normal) : Average size front speakers are connected to the receiver. 2 FRNT LRG (large) : Large front speakers are connected to the receiver. • For VR-615 (HTB model), do not select “LRG” (large) for front speaker as this will cause the speaker to malfunction. • For “FRNT LRG” selection, no sound will be heard from subwoofer speaker even when it is set to ON. However, if you select CINEMA EQ when subwoofer is selected, you will be able to hear sound from the subwoofer. When in STEREO mode, the sound goes directly to front speaker. 5 Press the SET UP key to accept the setting. • The center speaker setting indication “CNTR” appears. 6 Use the MULTI CONTROL knob or keys to select the appropriate center speaker setting. If you selected “LRG” as the front speakers setting, 1 CNTR NML (normal) : An average size center speaker is connected to the receiver. 2 CNTR LRG (large) : A large center speaker is connected to the receiver. 3 CNTR OFF : Center speaker setting mode to the receiver is OFF. • For VR-615 (HTB model), do not select “LRG” (large) for center speaker as this will cause the speaker to malfunction. If you selected “NML” as the front speakers setting, 1 CNTR ON : Center speaker setting mode to the receiver is ON. 2 CNTR OFF : Center speaker setting mode to the receiver is OFF. 7 Press the SET UP key again to accept the setting. •The surround speaker setting indication “SURR” appears. 8 Use the MULTI CONTROL knob or keys to select the appropriate surround speaker setting. If you selected “LRG” as the center speaker setting, 1 SURR NML (normal) : Average size surround speakers are connected to the receiver. 2 SURR LRG (large) : Large surround speakers are connected to the receiver. 3 SURR OFF : Surround speaker setting mode to the receiver is OFF. Continued to next page 17 EN Preparing for surround sound Preparing for surround sound ForVR-615(HTBmodel), do not select “LRG” (large) for surround speaker as this will cause the speaker to malfunction. If you have selected other than “LRG” as the center speaker setting, 1 SURR ON : Surround speaker setting mode to the receiver is ON. 2 SURR OFF : Surround speaker setting mode to the receiver is OFF. 9 Press the SET UP key again to accept the setting. • The subwoofer re-mix setting indication “SW RE-MIX” scrolls across the display. “SW RE-MIX” scrolls across the display. • If subwoofer is turned OFF, subwoofer re-mix setting is not visible. 0 Use the MULTI CONTROL knob or keys to select the appropriate subwoofer remix setting. 1 RMX ON : Subwoofer re-mix set mode to the receiver is ON. 2 RMX OFF : Subwoofer re-mix set mode to the receiver is OFF. ! Press the SET UP key to accept the setting. • The receiver enters the speaker volume level adjustment mode. • In step 4 and 5, indications appear only for the selected channels of the speakers that require adjusting. 4Adjust the speaker volume level. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. 1 Press the SET UP key to begin TEST TONE. 1 AUTO 2 MANUAL 2 The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or keys. Press the SET UP key again to select either AUTO or MANUAL. Use the MULTI CONTROL knob or keys to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the test tone is heard from the speakers in the following sequence for 2 seconds each: The channel indication blinks while the test tone is being ouput. • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. . • If the speaker setting selects are OFF, the speaker level settings are reset. 3 Press the SET UP key. • The test tone is turned off. The receiver enters the mode for inputting the distance to the speakers. 4 For MANUAL selection, press the SET UP key each time to select the speaker channel. 5Input the distance to the speakers. 1 Select the DISTANCE from the set up displays and press the SET UP key again. 2 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distan...

Descargar ahora

Introduzca dos números de la imagen: