Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 GLOSSARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 SAFETY INSTRUCTION GBImportant remarks on operation The following section contains important remarks concerning the operation, location and connection of the receiver. Please read these instructions carefully before using the unit for the first time. Extended absence/use during adverse weather conditions Always switch off the unit during periods of extended absence and during thunder storms by means of the power switch located on the front right-hand side. This also applies to other units that are connected to the receiver. Check if the timer is programmed and switch the unit on again in sufficient time for the recording. Mains cable Ensure that the mains cable (power supply cable) is not damaged. Never use the unit if the mains cable is damaged. Cleaning Disconnect the mains cable before cleaning the unit. For cleaning purposes use a dry cloth and only clean the surface of the unit. Do not open the casing under any circumstances due to risk of electric shock if contact is made with any parts inside the unit. Children Take care that children do not insert any objects into the ventilation slots due to danger of electric shock. Repair Any repairs or adjustments may only be performed by qualified personnel. The warranty will become void if the user attempts to open and repair the unit. Improper intervention may interfere with the electrical safety of the unit. The manufacturer assumes no liability for any accidents suffered by the user if the unit has been opened. Connection Incorrect connection may result in incorrect operation or defects in the equipment. Important remarks on location and assembly Location All electronic equipment generates heat, which is however not dangerous. Delicate furniture surfaces and finishes may become slightly discoloured over time due to the permanent heat source. Likewise, the feet of the equipment may cause discolouring on treated surfaces. If need be, place the unit on a suitable mat. Ventilation Heat occurring in this unit is discharged adequately. However, never install the receiver in a cabinet or on a shelf where there is inadequate ventilation. Never cover the ventilation slots of the unit. Never place any objects on the unit and ensure that there is a space of at least 10 cm above the unit to ensure that any heat occurring is discharged. Humidity, sunlight, heat Protect the unit from humidity, water droplets and spraying. Do not locate the receiver in the vicinity of a heating source and avoid exposing it to direct sunlight. Electrical supply Operate the unit only using a power source of 230 V/50 Hz. Connect the unit to the power supply and switch on only after it has been connected to the antenna and television unit. Earth Ensure that the parabolic antenna is correctly earthed observing the relevant local and/or CE regulations. Remote control Insert the batteries supplied in the remote control. Ensure that the battery polarity is correct observing the + and - markings in the battery compartment. «This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.» CONNECTIONS The following connections are located on the back of the unit: GB 1 234567 1 - 230 V/50 Hz: Connect the power cable to the power socket. 2 - Digital Audio TV: Digital (coaxial) audio output. AUDIO TV L & R: Audio output, left and right-hand channel for connecting to a stereo unit. 3 - TV: Connect the TV connection socket to your television unit using the SCART cable supplied. 4 - VCR: VCR SCART socket for connecting a video recorder. 5 - DATA INTERFACE: RS 232 interface for serial data transfer during servicing. 0-modem cable (pins 2 and 3 crossed, pins 1, 4, 6-9 are not used). Receiver: PC: Pin 2 = RXD Pin 2 = RXD Pin 3 = TXD Pin 3 = TXD Pin 5 = GND Pin 5 = GND 6 - SAT-IF INPUT: Sat-IF signal input and output for LNB supply and control signals connect the cable of your satellite unit to this socket. 7 - SAT-IF OUTPUT: IF signal output (e.g. for feeding through an analogue receiver). Note: The label showing the type and serial number is underneath your receiver. YOUR REMOTE F : Choose favourite channel list Menu: Change transparency of On-Screen-Display (OSD). I : Display Short and extended information (if broadcasted) about current and next programmes. : Change channels up by one unit...