Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Part Number Port One - Copper Port Two - Duplex Fiber-Optic 10Base-T/100Base-TX 100Base-FX SBFTF1011-150 RJ-45 ST, 1300 nm multimode 100 m (328 ft)* 2 km (1.2 miles)* SBFTF1013-150 RJ-45 SC, 1300 nm multimode 100 m (328 ft)* 2 km (1.2 miles)* SBFTF1014-150 RJ-45 SC, 1310 nm single mode 100 m (328 ft)* 20 km (12.4 miles)* SBFTF1015-150 RJ-45 SC, 1310 nm single mode 100 m (328 ft)* 40 km (24.8 miles)* SBFTF1018-150 RJ-45 MT-RJ, 1300 nm multimode 100 m (328 ft)* 2 km (1.2 miles)* SBFTF1029-150** RJ-45 SC, 1310 mn (TX)/1550 nm (RX) 100 m (328 ft)* single mode, 20 km (12.4 miles)* SBFTF1029-151** RJ-45 SC, 1550 mn (TX)/1310 nm (RX) 100 m (328 ft)* single mode, 20 km (12.4 miles)* SBFTF1029-152*** RJ-45 SC, 1310 mn (TX)/1550 nm (RX) 100 m (328 ft)* single mode, 40 km (24.8 miles)* SBFTF1029-153*** RJ-45 SC, 1550 mn (TX)/1310 nm (RX) 100 m (328 ft)* single mode, 40 km (24.8 miles)* * Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network. (TX) = transmit (RX) = receive * * SBFTF1029- 150 and SBFTF1029- 151 are intended to be installed in the same network where one is the local converter and the other is the remote converter. *** SBFTF1029- 152 and SBFTF1029- 153 are intended to be installed in the same network where one is the local converter and the other is the remote converter. Installation . . . . . . . . . . . . . . . . . .2 Operation . . . . . . . . . . . . . . . . . . .5 Cable Specifications . . . . . . . . . . .7 Technical Specifications . . . . . . . .9 Troubleshooting . . . . . . . . . . . . .10 Contact Us . . . . . . . . . . . . . . . . .11 Compliance Information . . . . . . .12 SBFTF10xx- Installation CAUTION: Wear a grounding precautions when setting Failure to observe this could result in damage to, Set the 4-Position Switch • The 4-position switch is located Auto-Negotiation (up=Enabled) on the side of the media Copper Mode (up=Full-Duplex) converter. Speed (up=100Mb/s) • Use a small flat-blade screwdriver Fiber Mode or a similar device to set the (up=Full-Duplex) recessed switches. • Refer to the drawing for the locations of the four individual 1234 switches. 1. Auto-Negotiation Up Enables Auto-Negotiation on the copper port. Advertises 100 Mb/s full-duplex and half duplex, and 10 Mb/s full-duplex and half duplex. Down Disables Auto-Negotiation on the copper port. 2. Copper Mode (Applies only if switch 1 is down. ) Up Forces full-duplex operation on the copper port. Down Forces half-duplex operation on the copper port. 3. Speed (Applies only if switch 1 is down. ) Up Forces 100 Mb/s operation on the copper port. Down Forces 10 Mb/s operation on the copper port. 4. Fiber Mode Up Forces full-duplex operation on the fiber port. Down Forces half-duplex operation on the fiber port. Installation -- Continued CAUTION: Wear a grounding precautions when setting Failure to observe this result in damage to, and Set the Jumper The Far-End Fault jumper is labeled Far-End Fault and “FD” for disable Far-FE FD page 6). Enable Far-End Fault Enable A fault on the fiber link causes the media converter to transmit a Far-End Fault signal. FE FD Disable No Far-End Fault signal is transmitted when Disable Far-End Fault a fault occurs. To set the jumper: 1. Using a small screwdriver, remove the four (4) screws that secure cover and carefully remove the cover from the media converter. 2. Locate the jumper on the circuit board labeled “FE” and “FD”. 3. Using small needle-nosed pliers or similar device, move the jumper to the desired position. (Refer to the drawings above.) 4. Carefully replace the cover on the media converter and replace the four (4) screws that secure the cover to the media converter. 24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. SBFTF10xx- Installation -- Continued Install the Fiber Cable 1. Locate or build 100Base-connectors installed at both 2. Connect the fiber cables to the • Connect the male TX cable connector to the female TX connector. • Connect the male RX cable connector to the female RX connector. 3. Connect the fiber cables to the other device hub, etc.) as described: • Connect the male TX cable connector to the female RX connector. • Connect the male RX cable connector to the female TX connector. Connect the fiber cable Connect the fiber cable to the media converter to the other device as shown. (media converter, hub, etc.) as shown RX TX RX TX Install the Twisted-Pair Copper Cable 1. Locate or build 10Base-T or 100Base-TX copper cables with male, RJ-45 connectors installed at both ends. 2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port connector on the media converter. 3. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port connector on the other device (switch, workstation, etc.). NOTE: The MDI (straight-through) or MDI-X (crossover) cable connection is configured automatically, ...