Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
However, you should make adjustments corresponding to your specifi c car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying the kits. CAUTIONS AND NOTES This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. • This unit uses BTL (Balanced Transformerless) amplifi er circuitry, i.e., fl oating ground system, so please comply with the following: Do not connect the “·” terminals of the speakers to each other. Do not connect the “·” terminals of the speakers to the metal body or chassis. • Cover the unused terminals with insulating tape to prevent them from short circuiting. • When an extension lead is used, it should be as thick and short as possible; connect it fi rmly with insulating tape. • Be sure to leave an appropriate space between the antenna and the wires of this unit. • When replacing the fuse, only use a 30 A fuse. • Do not let pebbles, sand or metallic objects get inside the unit. • To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off periodically. • Listening to the tape, radio, CD or Digital Audio Player, etc. with the volume set at a high level for a long period of time will exhaust the battery, while the engine is turned off or while the engine is idling. • This unit becomes very hot. Be careful not to touch the unit not only when using but for a while after using. DO NOT disassemble the units since there are no user serviceable parts inside. TERMINAL CONNECTIONS POWER SUPPLY LVT1699-001A [J] A B SPEAKER SYSTEMS Make sure to comply with the following notes: • Be sure not to connect the “·” terminals of the speakers to a common point. • If the ground wire is common to both left/right and front/rear speaker wirings, this unit cannot be used. Always use the independent lead wires for the speakers to be used. In this case, redo the wirings. • Use the speakers with an impedance of 1 . to 8 . for KS-AR7501D or 2 . to 8 . for KS-AR7001. • Use the speakers which have suffi cient capacity to the unit. The proper lead wire connected to each SPEAKER OUTPUT terminal is as follows. AWG 18 to AWG 8 (The cross section is about 0.8 mm2 to 8 mm2.) C A Mount this unit on a fi rm surface, such as in the trunk room or under the front seat. • Since heat is generated in the unit, do not mount it near infl ammable objects. In addition, mount it in an area that will not prevent the unit from dissipating the heat. • Do not mount the unit in the places subject to heat: near a radiator, in a glove compartment or in insulated areas such as under a car mat that will prevent the unit from dissipating heat. • When mounting the unit under the front seat, make sure that adjusting the seat position will not catch any wire of the unit. B When mounting this unit, be sure to use the provided screws. If any other screws are used, there is a risk of loosening the unit or damaging parts inside it. • Before drilling holes in the trunk to install the unit, make sure that there is a suffi cient space under the trunk so that you do not drill holes in the fuel tank, etc. • Detach the control cover on the unit before mounting (see "CONTROLS" on page 3). • To detach and rotate the Logo Plate 180 degrees, use the provided hex wrench (3 mm). C When you use more than one KS-AR7000 series’ amplifi er, you can pile them up to three with provided brackets, screws and washers in two ways, X or Y. Be sure to mount the lowest amplifi er (1) primarily following B. • Before piling amplifi ers, attach the provided spacers to "+" on the bottom of the amplifi ers 2 and 3. • Fix the amplifi ers on both sides with proper brackets as illustrated. Brackets (L) are used only for the amplifi er 3. • Before piling amplifi ers as X, fi rst make the connections for the power supply (see "POWER SUPPLY") and speakers (see "SPEAKER CONNECTIONS" on page 2). • It is recommended to pile amplifi ers as X so that you can easily operate the controllers on each amplifi er. X Y This unit is designed to be connected to subwoofers. Thank you for purchasing an ARSENAL product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. For safety.... • Do not raise the volume level too much, as this will block outside sounds, making driving dangerous. • Stop the car before performing any complicated operations. Logo Plate (detachable) CAUTION To prevent short circuits while making connections, keep the battery’s negative terminal disconnected. • When using a power cord (purchased separately), be sure to place the 40 A fuse near the battery as shown. • Connect the lead wire (power cord) through which power is supplied directly to the battery’s “.” terminal only after all the other connections have been made. The proper lead wire connected to each POWER terminal is as follows. • + B and GND: AWG 8 to AWG 4 (The cross section is about 8 mm2 t...
Otros modelos de este manual:El receptor y el amplificador - KS-AR7501D (2.36 mb)