Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
2. Radio Frequency devices operating nearby in same frequency band Check for other devices in the home or neighboring dwellings and relocate if possible ©2008 • All rights reserved. DLA2/4/6 Speaker Level Audio Router Appendix A: Specifications DLA2/4/6 Power Input +12 VDC, 2.1 Amps Amplier Impedance 4 - 8 Ohms Speaker Impedance 4 - 8 Ohms Frequency Response 20 HZ to 20 kHZ +/- 1 dB Power Handling Per Channel: 125 Watts RMS Max Attenuation -56 dB @ Last Step Dynamic Range 43 dB over 12 steps THD < 1% Connections Power 2.1 mm Jack Amplier Input 4 Position Flip-lock Connector (16AWG Speaker Wire) Speaker Output 4 Position Flip-lock Connector (16AWG Speaker Wire) Sense Inputs 2.1mm Jack IR Input 4 Position Flip-lock Connector Page/Doorbell Trigger In 3.5mm Mono Jack IR Emitter Output 3.5 mm Mono jack RF Input (ATON Port) RJ-11 jack Dimensions H x W x D (w/ feet) DLA2 DLA4/DLA6 Unit Height w/ Feet 2 3/16" x 8 1/2" x 7 5/8" (5.6cm x 21.6cm x 19.4cm) 2 3/16" x 17" x 8 5/8" (5.6cm x 43.2cm x 21.9cm) 1 3/4" (4.5cm) Weight DLA2 DLA4 DLA6 4.95lbs (2.3kg) unit weight 5.7lbs (2.6kg) shipping weight 10.15lbs (4.6kg) unit weight 11lbs (5kg) shipping weight 12.15lbs (5.5kg) unit weight 13lbs (5.9kg) shipping weight © 2008 • All rights reserved. 30 ©2008 • All rights reserved. DLA2/4/6 Speaker Level Audio Router Appendix B: Room Identification Labels Use the included Room Identi cation Labels to customize the DLA2/4/6 front panel. Place the labels in the oval Room Label Locations located below the Room Select Buttons. Figure B:1 Room Identi cation Labels To place a Room Identi cation Label: 1. Choose an appropriate label for the room. 2. Make sure that the oval Room Label Location on the face of the DLA2/4/6 is clean and oil free. 3. Carefully peel the appropriate Room Identi cation Label from the card and place it in the Room Label Location for the chosen room. © 2008 • All rights reserved. 31 DLA2/4/6 Speaker Level Audio Router Appendix C: Remote Control Options Option #1: DLA Slimline Remote (DLAIRM) Any combination of DLA remote control options may be used on a single DLA2/4/6 system. Use the included DLAIRM IR Remote Control to program DLA IR codes into a thirdparty universal/learning remote. Universal/Learning IR Remote Control DLAIRM Figure C-1: Universal Remote Use the DLAIRM as an IR remote for any individual room. Each room that is to be controlled with the DLAIRM requires an IR receiver wired into that speci c room’s IR Input as shown in Figure C-2. IR Input Cat-5 AIR5 DLAIRM Figure C-2: DLAIRM as Room Controller DLA2/4/6 Speaker Level Audio Router Figure C-3 : DLAIRM Remote Button Function ALL ON Turns all Rooms ON ALL OFF Turns all Rooms OFF SCENE Places Rooms into Scene Preset Mode MUTE (Toggle) Press to Reduce Volume of Room to 0 Press Again to Restore Volume to Previous Level Volume + Increases Volume of Room by One Step Press & Hold to Ramp Volume Up Volume Decreases Volume of Room by One Step Press & Hold to Ramp Volume Down Table C-1: IR Remote Functions ©2008 • All rights reserved. © 2008 • All rights reserved. 33 DLA2/4/6 Speaker Level Audio Router Option #2: DLA RF Remote & Receiver Kit DLA2RKT, DLA4RKT, DLA6RKT The DLA RF Remote & Receiver Kits (DLA2RKT, DLA4RKT and DLA6RKT) use Radio Frequencies (RF) to control the DLA system from anywhere in the home, up to 200 feet away. It is not necessary to point the remote at the main unit in order for it to function. Simply connect the RF Receiver base to the ATON Port on the rear of the unit as shown in Figure C-5. Place the receiver in a convenient location; preferably as high as possible. The RF Receiver Base utilizes mounting holes to mount the unit to a wall, cabinet or other surface. Figure C-4: DLA2RKT, DLA4RKT, DLA6RKT RF INPUT PATENT PENDING PWR IN 12VDC / 2.1A AMPLIFIER INPUT IR EMITTER OUTPUTS RF Receiver DLA2/4/6 Rear View Mounting Holes RJ-11 Plug X X Mounting Bracket Tabs Mounting Bracket SENSE INPUT 9VDC/100mA Figure C-5: RF Base Connection DLA2/4/6 Speaker Level Audio Router Additional RF Remotes (DLA2RM, DLA4RM, DLA6RM) Up to six additional DLA RF Remotes can be added to an exisiting RF receiver, providing convenient RF control for the entire family. Programming additional remotes can be accomplished in a matter of seconds. See the DLA RF Remote Instruction Sheet for more information. ROOM 1 ROOM 2 ROOM 3 ROOM 4 ROOM 1 ROOM 2 ROOM 1 ROOM 2 ROOM 3 ROOM 4 ROOM 5 ROOM 6 1 ALL ON SCENE VOL + ALL OFF MUTE – VOL ALL ON VOL + ALL OFF MUTE – VOL ALL ON VOL + ALL OFF MUTE – VOL 2 1 2 3 4 1 2 3 4 5 6 SCENE SCENE DLA2RM DLA4RM DLA6RM Figure C-6: DLA2RM, DLA4RM, DLA6RM Option #3: Third-Party Universal/Learning Remote Control The DLA2/4/6 can be controlled with virtually any brand of universal/learning remote by downloading DLA discrete IR codes from ATON’s website; These codes can then be imported into most universal/learning remote software applications and transferred into the universal remote. Tables C-2 through C-4 list all of the...
Otros modelos de este manual:Altavoces - DLA2 (885.85 kb)
Altavoces - DLA2 (885.85 kb)
Altavoces - DLA4 (885.85 kb)