Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
DLA2/4/6 Speaker Level Audio Router PAGE/DB TRIGGER IN Connection The Page/Doorbell Trigger Input (PG/DB TRIG IN) needs to be connected when the DLA2/4/6 is installed as part of a “sub-zone” of an ELAN® Multi-Room Controller, such as the S8.6 or S12, which utilizes an ELAN COM2 Communications Controller. This application allows the DLA Room Outputs to pass an audible tone through the room’s speakers at a preset level when the home’s doorbell is activated. To congure the PG/DB TRIGGER IN, simply connect a mono 3.5mm interconnect cable between the Page/Doorbell Trigger Out of the ELAN Multi-Room Controller and the PG/DB TRIGGER IN of the DLA2/4/6 as shown below. S8.6 IR EMITTER OUTPUTS PAGE/DB TRIG IN DLA2/4/6 3.5mm Mono Interconnect Cable Figure 3-9: PAGE/DB TRIG IN Connection ©2008 • All rights reserved. DLA2/4/6 Speaker Level Audio Router IMPEDANCE MATCH DIP Switches The IMPEDANCE MATCH DIP Switches are designed to allow various speaker loads to work safely with variously rated ampliers. Speakers rated between 4 Ohms and 8 Ohms can be matched with ampliers also rated from 4 to 8 Ohms. To set IMPEDANCE MATCH DIP Switches: 1. Determine the average impedance of all connected speakers (listed on the speaker or in the owner’s manual). 2. Determine the minimum impedance rating of the amplier (listed on the ampli er or in the owner’s manual). 3. Set the AMP DIP Switch to the minimum impedance rating listed on the ampli er/receiver. 4. Set the SPKR DIP Switch to the average impedance of all connected speakers. Note: Most speakers are 4 or 8 Ohms. In cases where 6 Ohms speakers are used, place the SPKR DIP Switch in the 4 Ohm position. Note: When using this setting, maximum volume is reduced to 10 steps. Figure 3-10: Impedance Match DIP Switch Settings © 2008 • All rights reserved. DLA2/4/6 Speaker Level Audio Router 4. Settings & Operation Functions of the DLA2/4/6 may be controlled from the Front Panel controls, through optional IR Receivers connected to the IR INPUTS, or with the optional RF Remote. Volume Settings Receiver/Ampler Volume Settings Prior to setting volume levels of the DLA2/4/6, proper volume level must be set of the Receiver/ Amplier. To set proper Receiver/Amplier volume level: 1. Turn on the Receiver/Amplier and start an audio source (CD Player, Radio, etc.). 2. Adjust the Receiver/Amplier level to the lowest setting. 3. Set the Receiver/Amplier to Stereo and disable any surround sound or DSP modes or “Sound Fields”. 4. If using a Receiver/Amplier with “A/B” speaker outputs, select the “B” speak- ers and turn off the “A” speakers for maximum output to the DLA2/4/6. Note: When the DLA2/4/6 is not in use, turn off the “B” speakers and turn on the “A” speakers for normal operation. 5. Turn on one room of the DLA2/4/6 and adjust the volume level to maximum. 6. While listening to the room turned on in the previous step, slowly adjust the re- ceiver/amplier volume to the loudest level possible without distortion. Make a note of the receiver/amplier level for future reference. RECEIVER/AMPLIFIER LEVEL 7.Turn on each room of the system and adjust the volume of the DLA2/4/6 to a comfortable level. Volume Status Bar The front panel includes a Volume Indicator LED bar with 11 LED’s located above the All On/ Off and Volume -/+ buttons. The Volume Indicator LEDs display the Volume for whichever Room is selected. When a Room is selected and ONE LED is lit, that room is at minimum volume. When a Room is selected and ALL LEDs are lit, that room is at maximum volume. Volume Status Bar Figure 4-1: Volume Status Bar ©2008 • All rights reserved. DLA2/4/6 Speaker Level Audio Router Room Volume Adjustment 1. Press the Room 1 Selector Button - the Room 1 Indicator LED will light up RED (indicating that Room 1 is selected for adjustment). ROOM 1 ROOM 2 Press 2. Press VOL -or VOL + until the desired volume is obtained. Press ROOM 1 ROOM 2 OR 3. Press the Room 2 Selector Button - the Room 2 Indicator LED will light up RED (indicating that Room 2 is selected for adjustment), while the Room 1 Indicator LED will light up BLUE (indicating that Room 1 is ON). ROOM 1 ROOM 2 Press 4. Press VOL -or VOL+ until the desired volume is obtained. Press ROOM 1 ROOM 2 OR 5. Continue this process for each additional Room. © 2008 • All rights reserved. DLA2/4/6 Speaker Level Audio Router ALL ON/OFF Press the ALL ON/OFF Button to turn the speakers in both Room 1 and Room 2 ON or OFF. ROOM 1 ROOM 2 Press Max Turn-On Volume Level In order to guard against unexpected high volume levels when the system is turned on, a Maximum Turn-On Volume Level may be set for each room. If the volume level prior to turning the room off is lower or equal to the Maximum Turn-On Volume Level, the room will come back on at the last volume. If the volume level prior to turning the room off is higher than the Maximum Turn-On Volume Level, the room will come back on at the Maximum Turn-On Volume Level instead of the last volume. To set the Maximum Turn-On Volume L...
Otros modelos de este manual:Altavoces - DLA2 (885.85 kb)
Altavoces - DLA2 (885.85 kb)
Altavoces - DLA4 (885.85 kb)