Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
1 2 9463 Knob-tines/PTO clutch lever, 30 9911 Lockwasher—hi-collar, 1/4"............ 1 tapered, plastic.......................... 1 31 9672 Screw-socket hd., 1/4-20 x 3/8"... 1 3 2263 Detent Plate-tines/PTO clutch lever (incl.Ref. No. 4)......................... 1 DRIVE SHAFT ASSEMBLY 4 1900758 Decal-operating instructions, detent 32 This Ref. No. not used.................. plate........................................... 1 33 9500 Retaining Ring-external................ 1 5 1186347 Bolt-flanged hex hd., 34 1909139 Dog Clutch-power unit................. 1 3/8-16x1-1/2".......................... 4 35 9301 Key-3/16 sq. x 1".......................... 3 6 — This Ref. No. not used.................. 36 1100004 Bolt-hex hd., 5/16-24x3/4", self- 7 1186329 Bolt-flanged hex hd., locking flange, Grade 5.............. 1 5/16-18x3/4", Grade 5............ 1 37 9944 Washer-disc spring (concave)...... 1 8 This Ref. No. not used.................. 38 2107 Pulley—transmission drive, cast iron 1 9 9902 Washer-flat, 5/16", S.A.E.............. 1 39 50027 Washer-flat, hardened shoulder 10 1900870010 Bracket—shift levers (incl. Ref. 1-1/4"......................................... 1 No. 86), see (A)......................... 1 40 1186310 Bolt-hex hd., 1/4-20 x 3/4", front 1900870021 Bracket—shift levers (incl. Ref. bearing cap................................ 3 No. 86), see (B)......................... 1 41 .... This Ref. No. not used.................. 11 9362 Pin-spring, 1/8"............................ 1 42 1900879001 Cap-front bearing......................... 1 12 9838 Nut-castle (slotted), 1/2"-20, call 43 85030 Seal—oil, front bearing cap............ 1 Tech Service for tightening 44 1124-2 Gasket-front bearing cap.............. 1 instructions............................. 1 45 1224-1 Shim-front bearing cap,. 13 9934 Washer-shoulder, 1/2"................. 1 010" thick..............................As Req'd 14 9932 Washer-disc spring...................... 2 45 1224-2 Shim-as above, .030"...............As Req'd 15 Lever-wheel speed shift (see page 45 1224-3 Shim-as above, .005"...............As Req'd 4, Ref. No. 5 for part number)... 1 45 1224-4 Shim-as above, .062"...............As Req'd 16 1900869001 Cover-power unit transmission.... 1 46 1714 Bearing & Cup-tapered cone roller 17 1123 Gasket-transmission cover........... 1 bearing with cup (race). Cone and 18 1100045 Bolt-hex hd., 5/16-18 x 1", Grade 5, cup sold as set only................... 2 (remove with care)................... 1 47 11601 Shaft-main drive, power unit. Incl. 19 1186230 Nut-hex, 5/16“-18......................... 1 integral worm, plus two pressed- 20 1901439 Spring-neutral plunger (remove on cone roller bearings, two bearing with care).................................. 1 cups, two shoulder washers...... 1 21 1035 Plunger-neutral (remove with care) 48 9617 Seal—oil, drive shaft, rear.............. 1 (incl. Ref. No. 22)...................... 1 49 9517 Retaining Ring-(snap ring), internal........1 22 1901440 Clip Ring-retains neutral plunger.. 1 23 1186393 Nut-hex, flange locknut, 3/8“-16... 1 PINION SHAFT ASSEMBLY 24 1902004 Bolt-hex hd., 3/8-16x1-1/2", 50 9309 Pin-roll (spiral), 1/4 x 2"............... 2 threaded full length.................... 1 51 1060A Plug-retaining, pinion bearing (incl. Ref. No. 52)............................... 2 TINES/PTO CLUTCH LEVER ASSEMBLY 52 9604 O-Ring—retaining plug................... 2 25 1900878001 Lever-eccentric, tines/PTO clutch. 53 1132-1 Shim-retaining plug, 1-1/64" inner (also see Ref. No.’s 1, 2,3 and dia., .033" thick (on right side 4 listed above)........................... 1 only one #1132-1 shim is also 26 1100804 Bolt-hex hd., 1/4-20 x 1/2"........... 1 used between bearing and washer, 27 2123 Bushing-tines/PTO clutch lever Ref. No.’s 54 & 55).................... As eccentric shaft........................... 1 Req'd (continued) (A)~ For all models except 12166 (B)- For Model 12166 only 9 MODELS 12068, 12069, 12070, 12071, 12087, 12087C, 12088, 12088C, 12089, 12089C,12090, 12090C, 12166 POWER UNIT TRANSMISSION ASSEMBLIES (Figure 6 Continued) MODELS 12068, 12069, 12070, 12071, 12087, 12087C, 12088, 12088C, 12089, 120890,12090, 12090C, 12166 REF No. PART No. DESCRIPTION QTY. REF No. PART No. DESCRIPTION cm PINION SHAFT ASSEMBLY (continued) ECCENTRIC SHAFT ASSEMBLY 53 1132-2 Shim-same as 1132-1, ,062"thick As 71 9307 Pin-roll, 3/16" x 1-1/4" (spiral)..... 1 Req’d 72 1900880001 Lever-eccentric, wheel speed 53 1132-3 Shim-same as1132-1, .010" .... As shifting...................................... 1 Req'd 73 9622 Seal-oil, eccentric shaft................ 1 54 9404 Bearing—ball, pinion shaft............ 2 74 1442 Pin-eccentric shaft, wheel speed 55 1126 Washer-pinion shaft.................... 2 shifting..............................
Otros modelos de este manual:Herramientas de jardín - 12087C (2.11 mb)
Herramientas de jardín - 12090C (2.11 mb)