Votos - 6, Puntuación media: 4.2
(
)
)
|
Resumen del manual
The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. ERGONOMIC DESIGN The design of the trimmer provides for easy handling. It is designed for comfort and ease of grasp when operating in different positions and at different angles. GRASS DEFLECTOR The trimmer includes a grass deflector that helps protect you from flying debris. TOP-MOUNTED MOTOR The top-mounted motor improves balance and is located away from the dust and debris of the cutting area. Fig. 1d reel Easy string head pro cut II string head ASSEMBLY UNPACKING This product requires assembly. • Carefully remove the tool and any accessories from the box. Make sure that all items listed in the packing list are included. • Inspect the tool carefully to make sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. • If any parts are damaged or missing, please call 1-800-860-4050 for assistance. PACKING LIST CS30 Trimmer Assembly Pro Cut II String Head Spool Retainer Front Handle Curved Shaft Grass Deflector Bottle of -Cycle Lubricant Hanger Cap Operator’s Manual SS30 Trimmer Assembly Pro Cut II String Head Spool Retainer Front Handle Straight Shaft Grass Deflector Bottle of -Cycle Lubricant Hanger Cap Operator’s Manual BC30 Brushcutter Assembly “J” Handle Straight Shaft Grass Deflector Shoulder Harness Gear Head Locking Tool Pro Cut II String Head Spool Retainer Arbor Reel Easy String Head Assembly and Bolt Bottle of -Cycle Lubricant Hanger Cap Operator’s Manual WARNING: If any parts are damaged or missing do not operate this product until the parts are replaced. Failure to heed this warning could result in serious personal injury. WARNING: Do not attempt to modify this product or create acces- sories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. WARNING: To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts. 10 ASSEMBLY INSTALLING THE POWER HEAD TO THE ATTACHMENT See Figure 2. WARNING: Never install, remove, or adjust any attachment while power head is running. Failure to stop the engine can cause serious personal injury. The attachment connects to the power head by means of a coupler device. • Loosen the knob on the coupler of the power head shaft and remove the end cap from the attachment. • Push in the button located on the attachment shaft. Align thebuttonwiththeguiderecessonthepowerheadcoupler and slide the two shafts together. Rotate the attachment shaft until the button locks into the positioning hole. NOTE: If the button does not release completely in the positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place. • Tighten the knob securely. WARNING: Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious personal injury. REMOVING THE ATTACHMENT FROM THE POWER HEAD For removing or changing the attachment: • Loosen the knob. • Push in the button and twist the shafts to remove and separate ends. ATTACHING THE STORAGE HANGER See Figure 3. There are two ways to hang your attachment for storage. .To use the hanger cap, push in the button and place the hanger cap over end of the lower end attachment shaft. Slightly rotate the cap from side to side until the button locks into place. . • The secondary hole in the attachment shaft can be used for hanging purposes as well. Fig. cOuPLER knOB TRIMMER ATTAcHMEnT POwER HEAd SHAfT POSITIOnInG HOLE GuIdE REcESS Fig. 3 BuTTOn HOLE HAnGER cAP SEcOndARy HOLE BuTTOn 11 12 ATTACHING THE FRONT handle - CS30 and SS30 See Figure 4. . Remove wing nut, washer, and bolt from the front handle. . Install the front handle onto the top side of the drive shaft housing in the area indicated by the label. NOTE: The open side of the handle should face the operator. . Place the bolt through the front handle. NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle. . Reinstall the washer and wing nut. . Tighten wing nut securely. ATTACHING THE “J” HANDLE - BC30 See Figure 5. A “J” handle must be used for ensuring the best control and maximizing operator safety when using a brushcutter. . Hold the top and bottom clamp snugly in position on the shaft housing so that handle will be located to the operator’s left. . Insert the end of the handle between the clamps. . Align the bolt holes and push the long bolt (1/4-20 x 1-1/2 in.) through the handle side. . Place short bolt (1/4-20 x 1 in.) through opposite side of ...
Otros modelos de este manual:Herramientas de jardín - RY30951 (6.65 mb)
Herramientas de jardín - RY30931 (6.65 mb)
Herramientas de jardín - RY30971 (6.65 mb)