Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, lubricant, grease, etc. WARNING: Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating lubricants, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury. You can often make adjustments and repairs described here. For other repairs, have the trimmer serviced by an authorized service dealer. installing reEl easy string head See Figures 24 - 25. . Stop the engine and disconnect the spark plug wire. . Remove currently installed string head. . Open the Reel Easy String Head by depressing the latches on each side. The contents of the string head are spring loaded, so keep your other hand over the string head cover while depressing the latches. . Remove the string head cover, knob, and spool and set aside. . Place the string head on the drive shaft. Make sure the string head is fully seated. . Install the hex bolt into the opening on the drive shaft and secure using the hex-shaped opening in the knob to tighten. Fig. 25 Fig. 24 cover knob SPOOL SPRING string head STRAIGHT SHAFT CURVED SHAFT knob knob hex bolt hex-shaped opening lat ches lat ch opening hex bolt 22 MAINTENANCE Fig. 26 installing string in reel easy string head See Figures 26 - 27. Use .095 in. diameter monofilament string. . Stop the engine and disconnect the spark plug wire. . Cut one piece of string approximately 25 ft. in length. . Rotate knob on string head until line on knob aligns with arrows on top of string head. . Insert one end of string into eyelet located on the side of the string head and push until string comes out through eyelet on the other side. Continue to push string through the string head until the middle section of the string is inside the string head and string outside the string head is evenly divided on each side. . Rotate the knob on the string head to wind the string. If using the CS30, knob should be rotated counterclockwise. If using the SS30 or the BC30, knob should be rotated clockwise. Wind the string until approximately 8 in. remains protruding from the string head. installing pro cut II string head See Figure 28. . Stop the engine and disconnect the spark plug wire. . Remove currently installed string head. . Install the string head on the drive shaft until fully seated. . Install the spool retainer and turn counterclockwise for CS30 or clockwise for SS30 or BC30 to secure. . Install string as described in the next section of this manual. Fig. 27 spool retai ner string head drive shaft Fig. 28 align line on knob with arrows insert string to center and rotate knob to wind eyelet 23 installing string in pro cut II string head See Figure 29. Use monofilament string between .095 in. and .105 in. diameter. Use original manufacturer’s replacement string for best performance. . Stop the engine and disconnect the spark plug wire. . Gather two of the pre-cut lengths of trimmer line provided or cut two pieces of trimmer line, in 11 in. lengths. . Insert the strings into the slots located on the sides of the string head. String should be pushed in until approximately 1 in. protrudes from the holes on the top of the string head. . Remove old string by pulling it from the holes located on the top of the string head. CLEANING THE EXHAUST PORT AND MUFFLER NOTE: Depending on the type of fuel used, the type and amount of lubricant used, and/or your operating conditions, the exhaust port, muffler, and/or spark arrestor screen may become blocked with carbon deposits. If you notice a power loss with your gas powered tool, you may need to remove these deposits to restore performance. We highly recommend that only qualified service technicians perform this service. SPARK ARRESTOR The spark arrestor must be cleaned or replaced every 50 hours or yearly to ensure proper performance of your product. Spark arrestors may be in different locations depending on the model purchased. Please contact your nearest service dealer for the location of the spark arrestor for your model. Idle Speed Adjustment See Figure 30. If the cutting attachment turns at idle, the idle speed screw needs adjusting on the engine. Turn the idle speed screw counterclockwise to reduce the idle RPM and stop the cutting attachment movement. If the cutting attachment still moves at idle speed, contact a service dealer for adjustment and discontinue use until the repair is made. WARNING: The cutting attachment should never turn at idle. Turn the idle speed screw counterclockwise to reduce the idle RPM and stop the cutting attachment, or contact a service dealer for adjustment and discontinue use until the repair is made. Serious personal injury may result from the cutting attachment turning at idle. MAINTENANCE Fig. 29 hole slot slot insert strings ...