Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
Modification of this product can result in property damage. Dometic Sanitation Corporation 3 28 State Rt 226, PO Box 38, Big Prairie, OH 446 SeaLand Product Hotline -800-32 -9886 (8:00 a.m. - 5:00 p.m. ET) TAbLE of CoNTENTS Important Information ................................ 2 Toilet Model Identification ......................... 2 How to Use................................................2 Installation ................................................. 3 Proper Bowl Cleaning ............................... 4 Winterizing ................................................ 4 Deodorants and Special Tissue ................ 5 Troubleshooting ................................... 6 - 7 Warranty ................................................... 8 IMpoRTANT INfoRMATIoN . Do not use chlorine or caustic chemicals, such as laundry bleach or drain-opening types, in the system. These products damage the seals in toilets and dump valves. 2. Do not permit foreign objects (paper towels, paper cups, diapers, sanitary napkins, etc.) to be flushed through the toilet. 3. Mechanical seal toilets, like SeaLand models, are designed to only discharge directly into a holding tank. Horizontal pipe runs as found in conventional residential or commercial plumbing systems cannot be accommodated. 4. Toilet bowl must be regularly cleaned and winterized according to “Proper Bowl Cleaning” and “Winterizing” procedures on page 4, or your warranty coverage may be voided. ToILET MoDEL IDENTIfICATIoN The model identification label is located on the toilet base and will show the model number and serial number. For model 2 0 toilet, remove base cover to locate identification label (see page 3). DOMETIC CORPORATION P.O. BOX 38, 13128 STATE RT 226 (800) 321-9886 BIG PRAIRIE, OH 44611 USA MODEL NO. 000 SERIAL NUMBER 000000 HoW To uSE To prepare the SeaLand toilet for use, check to be sure water supply to the toilet is connected. Turn on water supply and check system for leaks. Flush toilet and check for leaks. To properly use the SeaLand toilet, follow these simple instructions: . To add water to the toilet, lift or raise the flush lever until desired water level is reached. Generally, more water is required only when flushing solids. 2. To flush toilet, push lever all the way down until contents leave toilet bowl. Water flow pressures vary at different locations, therefore holding the flush lever down for 4-8 seconds may be required. We require a minimum flow at the toilet of two gpm (7.6 lpm) for proper rim and bowl wash. 3. Release flush lever by allowing it to snap back, which permits positive sealing around the flush ball. 4. A small amount of water should remain in bowl. Note: Holding flush lever down longer than necessary results in excessive water usage. 2 INSTALLATIoN . To replace an older toilet, turn off water supply to toilet. Disconnect water line at toilet water valve. Unscrew floor bolt nuts and remove toilet. Discard old floor seal and mounting bolts. The old floor flange may be used if it is in good condition and fastener holes are positioned as shown in Figure A. Make sure center of floor flange is at least inches from back wall (Figure A). 2. If installing new floor flange, make certain that the toilet mounting bolts align properly with SeaLand toilet mounting pattern (Figure B). 3. Secure flange to floor using at least four flat-head screws (one each at the front, back, right and left sides of flange) through countersunk holes. Insert floor bolts into slotted holes at right and left sides of flange (Figure B). 4. Position floor seal by pressing the floor bolts up through holes in the seal. 5. Set toilet in place with bolts protruding up through mounting holes in base (Figure C). 6. Install washers and hex nuts provided with toilet. Snug nuts down equally with standard 7/ 6” open end wrench. Install two wood screws provided in two holes at rear of base. (Figure C). 7. If toilet is being installed in a shower stall, apply a /4” bead of glazing compound around the perimeter of the base (Figure D). 8. Connect water supply line to water valve ( /2” MPT) inlet using appropriate fittings or an extension (Figure E). 9. Turn on water supply and flush toilet to test for leaks. 10. Attach pedal cover to flush pedal (see instructions below) after making sure there are no leaks at connections. . FOR MODEL 2 0 ONLY, put base cover in front of toilet base, aligning flush pedal with opening on side of cover. Push base cover back until it locks into place, making sure it does not interfere with flush pedal operation (Figure F). Attaching pedal Cover . Align cover with pedal and press into place so that tab locks into space at rear of pedal. 2. To release cover, press on tab at back of pedal and pull cover off. CoVER Fig. A Fig. B fRoNT Fig. C Insert two wood screws in rear of base. Fig. D Fig. E Fig. F 3 pRopER boWL CLEANING For stubborn bowl stains, use SeaLand® Toilet Bowl Cleaner (Fig. A). It’s manufactured especially for use with SeaLand toi...
Otros modelos de este manual:Fontanería - SEALAND 210 (404.06 kb)