However, using the AOS CLI may be necessary for more advanced configurations. ACCESS THE GUI You may access the web-based GUI from any web browser on your network by following these steps: 1. Connect the switch to your PC using any of the 24 Ethernet ports on the front of the unit. 2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address, you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for instructions.) 3. Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1. 4. You will then be prompted for the username and password (the default settings are admin and password). 5. The initial GUI screen appears. ACCESS THE CLI Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the NetVanta switch CONSOLE port, you need the following items: • VT100 terminal or PC (with VT100 terminal emulation software) • Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end 1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the unit. 2. Connect the other end of the serial cable to the terminal or PC. 3. Provide power to the unit as appropriate. Refer to the NetVanta 1000 and NetVanta 1000R Series Hardware Installation Guide (provided on the ADTRAN OS System Documentation CD) for more details. 4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press to activate the AOS CLI. 5. Enter enable at the > prompt. 6. Enter the enable password when prompted. The default password is password. The configuration parameters used in the examples outlined in this document are for instructional purposes only. Please replace all underlined entries (example) with your specific parameters to configure your application. NETVANTA 1224R FRONT PANEL LAYOUT NETVANTA 1224STR (DC VERSION) REAR PANEL LAYOUT -48V....., 1.2A +24V....., 2.5A USE COPPER CONDUCTORS ONLY For more detailed documentation, visit us online at ® Quick Start Guide NetVanta 1224 Series Switches P/N 1200500E1/L1, 1200504E1/L1, 1200510L1,1200520E1/L1, 1200590L1 CONFIGURE THE UNIT’S IP ADDRESS The following steps create an IP address and subnet mask for the virtual interface vlan 1. If you are not sure what IP address to assign, please contact your network administrator. 1. At the # prompt, enter config terminal. 2. At the (config)# prompt, enter interface vlan 1 to access the configuration parameters for the virtual LAN (VLAN) interface. 3. Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the VLAN interface using a 24-bit subnet mask. 4. Enter no shutdown to activate the virtual interface to pass data. 5. Enter exit to return to the Global Configuration mode. Depending on your configuration, you may need to set a default gateway as well using the (config)#ip default gateway command. If IP routing is enabled on the unit, do NOT set a default gateway. ENABLE TELNET ACCESS The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password of password. 1. Verify that the prompt of your unit displays (config)#. 2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions. 3. Enter login to initiate Telnet access. 4. Enter password adtran to change the login password for the Telnet sessions. 5. Enter exit to return to the Global Configuration mode. 6. Verify that the prompt of your unit displays (config)#. 7. Enter do write memory to save the current configuration. ETHERNET PINOUTS Pin Name Description 1 TX1 Transmit Positive 2 TX2 Transmit Negative 3 RX1 Receive Positive 4, 5 — Unused 6 RX2 Receive Negative 7, 8 — Unused CONSOLE PINOUTS Pin Name Description 1 DCD Data Carrier Detect (output) 2 RD Receive Data (output) 3 TD Transmit Data (input) 4 DTR Data Terminal Ready (input) 5 SG Signal Ground 6 DSR Data Set Ready (output) 7 — Unused 8 CTS Clear to Send (output) 9 — Unused For information on installing the VPN Accelerator Card, please refer to the NetVanta 1000 Series Hardware Installation Guide on the ADTRAN OS System Documentation CD included in your switch shipment. CONFIGURE YOUR APPLICATION More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS System Documentation CD included in your shipment. For more detail on hardware setup, refer to the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on configuring your system, refer to the ADTRAN Operating System (AOS) Command Reference Guide, configuration guides, and technical support notes. Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on the ADTRA...
