Iniciar sesión: ACCUSYS, INC. 5F, 38 TAIYUAN ST, JHUBEI, HSINCHU, TAIWAN, R.O.C. TITLE EXPERAID COMMAND LINE INTERFACE USER GUIDE PROJECT “DESKTOP RAID” DOCUMENT STATUS OFFICIAL RELEASE REV. G–05-NOV-2007 PAGE 20 OF 27 3.3.4.3 Command Name Command Description RebuildParity Use this command to rebuild parity of an array which contains parity. i.e. RAID 5 or RAID 6. Parameter 1 Parameter Description Array No.:
This window is used for blocking group members’ access to specified URLs and/or for letting group members access specified URLs blocked at the minimum filtering level. Fig. 3:1-13 Exception URL window NOTE: Settings in this window work in conjunction with those made in the Override Account window and in the Minimum Filtering Level window maintained by the global administrator. Users with an override account will be able to access URLs set up to be blocked in this window, if the global administra
Computer networks have proved to be one of the fastest modes of communication but until recently only large businesses could afford the networking advantage. The OfficeConnect® product range from 3Com has changed this, bringing networks to the small office. As the power of workstations and business applications increases, heavier demands are made on the available network bandwidth that, if unchecked, can lead to performance problems in a hub-based setup. Installing the OfficeConnect Switch 400 (
¦ The 20-port 10/100BASE-TX Fast Ethernet Layer 2 Switching Module (Model Number 3CB9LF20R) has twenty 10/100 Mbps RJ-45 ports on its front panel and two 1-Gigabit ports on the back for connection to the chassis backplane. Each of these FEN Switching Modules operates as a Layer 2 switch and occupies a single switching module slot in the CoreBuilder 9000 7-slot chassis, 8-slot chassis, or 16-slot chassis. The 10/100BASE-TX and 100BASE-FX FEN Switching Modules support the following key features: ¦
WARNING: The “warning” icon is followed by information alerting you to a potential situation that may cause damage to property or equipment. CAUTION: The “caution” icon is followed by information warning you that a situation has the potential to cause bodily harm or death. Service Information The user should not attempt any maintenance or service on the unit beyond the procedures outlined in this document. Any initial hardware setup problem that cannot be resolved at your internal organization s
You can change these values as needed. 29 To enable the DHCP server for dynamic IP address allocation to the clients, select the “Enable” check box. The clients can get their IP address from a range of IP Pool Addresses. The Lease Time is the amount of time a client will be allowed to connect to the Router using the assigned IP address. You can enter your local domain name in the Local Domain Name field. 2-3-2 DHCP Client List The DHCP client list allows you to see which clients are connected to
3. Make sure the power cord is correctly and securely connected into the HomePortal. 4. Verify that both ends of the power cord are firmly plugged into the brick. Note: If the POWER indicator light is red (signifying a system error), or does not light after performing the steps above, contact 2Wire Customer Care. BROADBAND LINK indicator light is red If the BROADBAND LINK indicator light is red, the HomePortal has not established a connection to your DSL service provider: 1. Go to the HomePortal
Enter the directory in the Copy Files From entry box (usually C:\WINDOWS\OPTIONS\CABS), and then click OK. Files are copied. You are prompted for EtherDisk diskette 2. 5 Make sure that EtherDisk diskette 2 is in drive A, and then click OK. Files are copied. You are prompted to restart the PC. 6 Remove EtherDisk diskette 2 from drive A, and then click Yes to restart the PC. You must restart the PC to complete the installation. The installation is complete. Go to “Verifying Successful Installation
2 Press down gently on the unit to secure it onto the clip, ensuring the fastening pieces fit into the slots on the unit below, as shown in Figure 3 (picture 2). Figure 3 Stacking Your Units Together To remove the clip: 1 Remove the top unit together with the clip. If you hook a finger around one of the the fastening pieces and then pull it gently from out of the slot, the clip should come away with the upper unit attached to it. 2 Push the clip in the center, so it bends towards the base of the
