Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
When it is desired to keep the power on for a prolonged period in continuous use, the stopper can be used to keep the switch on even after the trigger has been released. (First pull the trigger, and then press the stopper.) To turn the switch off, first pull the trigger again to disengage the stopper. 4. Precaution after use Do not lay the sander down immediately after using on a place where there are many shavings, much dirt and dust until it has completely stopped revolving. CAUTION When the disc sander is not in use, the pwer source should be disconnected. ATTACHMENT/REMOVAL OF SANDING DISC (Fig. 2) CAUTION: Be sure to switch power OFF and disconnect the attachment plug from the receptacle to avoid serious trouble. (1) Attach wahser, rubber pad and sanding disc on the spindle, in that order. (2) While pushing the lock lever with one hand, lock the spindle by turning the rubber pad slowly with the other hand. Tighten the wheel washer by using the supplied wrench. . Remove the sanding disc in the reverse order to attachment. CAUTION: Confirm that the lock lever is disengaged by pushing lock lever two or three times before switching the disc sander on. MAINTENANCE AND INSPECTION 1. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 2. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 3. Inspecting the carbon brushes (Fig. 4) The motor employs carbon brushes which are consumable parts. Since an excessively worn carbon brush could result in motor trouble, replace the carbon brushes with new ones which have the same carbon brush No. shown in the figure when they become worn to or near the “wear limit”. In addition, always keep carbon brushes clean and ensure that they slide freely within the brush holders. 4. Replacing carbon brushes Disassemble the brush caps with a slotted-head screwdriver. The carbon brushes can then be easily removed. 5. Service parts list A: Item No. B: Code No. C: No. Used D: Remarks CAUTION Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATION Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice. NOTE Due to HITACHI’s continuing program of research and development, the specifications herein are subject to change without prior notice. 123417mm6mm43589076431215° – 30° 123417mm6mm43589076431215° – 30° 1 .. 2 . 3 .... 4 .. 5 .... 6 .. 7 ... 8 ..... 9 .... 0... ...... ..! ....... ....................../. ..... ................. (..). ...... (..) .... ......... 1).... a) ................... ..............b) .................... ............... ...............c) .................... .. .............2) .... a)............. . ........... .................. .................b) .................... ............ ................... .. c).................... ... ...............d) ....... -............ .............. ................... ....... .................e) ................... . ..............3) .... a).................... ...... .................. .. ................... ..... b)...... -......... ................... .................... ... c)..... -.............. .... ................... ................ d).................. . ................... . e).............. -..... .............. ................f) ..........-......... .......-............ ..... ................... . g).................... ............ ...............4) .......... a)........ -.......... ................... .. b)................. . ................... .. c).................... .... ..................d) ................... .;.................. ....... ................e) ...... -............. .................... ...... .............. ...............f) .......... ................... ... g).................... .................... .......... ................... .. 5).. a).................... .... ............. ....: ................. ...................... .. ............... 1...........2. ....... . .. 3.........4. ...................... ...5. .........6. ..................... ..7. ...................... ... . S18SB S15SB ..(...)*(110V, 115V, 120V, 127V, 220V, 230V, 240V) ....* 705W ...... 360W .....4500 ./. ...... 180 mm 150 mm ..(.....) 2.0 kg *................ . ...... .. S18SB S15SB180 mm ..*1 1 — 150 mm ..*1 — 1 ......
Otros modelos de este manual:Máquinas de rectificar - S 18SB (629.3 kb)