Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
NOS. 4330, 4330-01, 4335 —TYPE 1 10" HEAVY-DUTY BENCH GRINDER Bulletin 2928-1 P.T.I. SAFETY RULES FOR STATIONARY POWER TOOLS 1. KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn its .application and limitation, as well as the specific potential hazards peculiar to this tool. 2. KEEP GUARDS IN PLACE and in working order. 3. GROUND ALL TOOLS. If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical receptacle. If an adapter is used to accommodate a two-prong receptacle, the adapter wire must be attached to a known ground. Newer remove the third prong. 4. REM OWE ADJUSTING • KEYS AND WiiiCHES. Form habit of checking to see that keys and adjusting wrenches are removed before turning on tool. 5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 8. AVOID DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations. Keep your work area well illuminated. 7. KEEP CHILDREN' AWAY. Ail visitors should be kept a safe distance from work area. 8. MAKE WORKSHOP KIDPIOOF—with padlocks, master switches, or by removing starter keys. 9. DON’T FORCE TOOL. It will do the job better and be safer at the rate for which it was designed. 10. USE RIGHT TOOL. Don’t force tool or attachment to, do a job it was not designed for. 11. WEAR PROPER APPAREL. No loose clothing or jewelry to get caught in moving parts. 12. USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. 13. SECURE WORK. Use clamps or a vise to hold work, when practical. It’s safer than using your hand, frees both hands to operate tool. 14. DON’T OVERREACH. Keep your proper footing and balance at all times. 15.. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 16. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters. 17.' USE RECOMMENDED'ACCESSORIES. Consult owner’s manual. Use of improper accessories may be hazardous. 18. AVOID ACCIDENTAL STARTING. Make sure switch is off before plugging in cord. GROUNDING These units are equipped with an outlet box mounted on the back of the unit for permanent wiring, as required by Underwriters Laboratories. Wiring diagrams are pasted to the underside of the base. To insure proper wiring & “grounding” of tool, have connection made by a qualified electrician. LUBRICATION This tool is equipped with lubricant sealed ball bearings which require no further lubrication for the life of the bearing. MOTOR Four pole capacitor start induction motor. Squirrel cage rotor. Cat Rated RPM No. Phase HP ■ Cycles @ 115 V. No Load Voltage, A.C. 4330 1 1 50/80 14.6/13 1500/1800. 115 Volts 4330-01 1 1 50/80 14.6/13 1500/1800 220 Volts 4335 3 1 50/60 14.6/13 1500/1800 220/440 Reconnectable CHANGING WHEELS Remove 4 screws holding wheel guard cover. Loosen and remove hexagon nut. (Nut on left wheel has left hand threads, nut on right wheel has right hand threads) and clamp washer. Remove wheel. To reassemble, reverse above steps. Do not overtighten nut. Wheel size 10" O.D., 3/4" I.D., 1" Width. ACCESSORIES No. 34575 One Shatter-Proof Eye Shield . . . Fastens permanently to Bench Grinder. Adjusts quickly to various positions to suit operator. Not illuminated. (Replacement glass, No. 34578). No. 19115 Cutter Wheel Dresser . . . Has spare set of cutter wheels. Dresses wheels quickly for fast grinding. No. 21961 Diamond Dresser . . . Produces an accurate, smooth face for finish grinding. No. 53536 Pedestal . . . Holds grinder at convenient height. Has detachable water pot. Height; 31%"; Base: 16 square. Grinding Wheels (10" Diam. x 1" Face x %" Hole): No. 10274 Specification A24Q6V, Type 1 No. 10275 Specification A46N6V, Type 1 Wire Wheel Brushes (10" Diam. x 1%" Face x W Hole: No. 21407 ’ .014 Wire Diam. (30 Gage) No. 27012 .0118 Wire Diam. (33 Gage) Cotton Buffing Wheels (10" Diameter x 2/4" Hole): No. 26873 % " Wide . No. 26876 .Va” Wid...
Otros modelos de este manual:Máquinas de rectificar - 2928-1 (2.96 mb)
Máquinas de rectificar - 4330 (2.96 mb)
Máquinas de rectificar - 4335 (2.96 mb)