Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Keep your proper footing and balance at all times. 15.. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 16. DISCONNECT TOOLS before servicing and when changing accessories such as blades, bits, cutters. 17.' USE RECOMMENDED'ACCESSORIES. Consult owner’s manual. Use of improper accessories may be hazardous. 18. AVOID ACCIDENTAL STARTING. Make sure switch is off before plugging in cord. GROUNDING These units are equipped with an outlet box mounted on the back of the unit for permanent wiring, as required by Underwriters Laboratories. Wiring diagrams are pasted to the underside of the base. To insure proper wiring & “grounding” of tool, have connection made by a qualified electrician. LUBRICATION This tool is equipped with lubricant sealed ball bearings which require no further lubrication for the life of the bearing. MOTOR Four pole capacitor start induction motor. Squirrel cage rotor. Cat Rated RPM No. Phase HP ■ Cycles @ 115 V. No Load Voltage, A.C. 4330 1 1 50/80 14.6/13 1500/1800. 115 Volts 4330-01 1 1 50/80 14.6/13 1500/1800 220 Volts 4335 3 1 50/60 14.6/13 1500/1800 220/440 Reconnectable CHANGING WHEELS Remove 4 screws holding wheel guard cover. Loosen and remove hexagon nut. (Nut on left wheel has left hand threads, nut on right wheel has right hand threads) and clamp washer. Remove wheel. To reassemble, reverse above steps. Do not overtighten nut. Wheel size 10" O.D., 3/4" I.D., 1" Width. ACCESSORIES No. 34575 One Shatter-Proof Eye Shield . . . Fastens permanently to Bench Grinder. Adjusts quickly to various positions to suit operator. Not illuminated. (Replacement glass, No. 34578). No. 19115 Cutter Wheel Dresser . . . Has spare set of cutter wheels. Dresses wheels quickly for fast grinding. No. 21961 Diamond Dresser . . . Produces an accurate, smooth face for finish grinding. No. 53536 Pedestal . . . Holds grinder at convenient height. Has detachable water pot. Height; 31%"; Base: 16 square. Grinding Wheels (10" Diam. x 1" Face x %" Hole): No. 10274 Specification A24Q6V, Type 1 No. 10275 Specification A46N6V, Type 1 Wire Wheel Brushes (10" Diam. x 1%" Face x W Hole: No. 21407 ’ .014 Wire Diam. (30 Gage) No. 27012 .0118 Wire Diam. (33 Gage) Cotton Buffing Wheels (10" Diameter x 2/4" Hole): No. 26873 % " Wide . No. 26876 .Va” Wide CAUTION: Recommended accessories for your Bench Grinder are listed above. The use of any other accessory might be more hazardous. ADDITIONAL GRINDER SAFETY RULES 1. Always wear safety glasses or other eye protection when operating this tool, and . eye shields, mounted on the wheel guards, are strongly recommended. 2. Replace a cracked wheel immediately. Handle grinding wheels carefully to avoid bumping or dropping. DO NOT use a grinding wheel that has been dropped. Before using, inspect each grinding wheel for cracks or flaws and if these are evident, discard the wheel. 3. Before mounting a new wheel, be sure that it is marked with an R.P.M. that is the same as, or higher than, the no-load speed of the grinder as marked on the nameplate. Do not overtighten wheel nut. Use only flanges furnished with this grinder. 4. Never start a grinder with anyone, including the operator, standing in line with the wheel. After installing a replacement wheel, stand to one side and allow it to revolve freely for about one minute. 5. Do not grind on the sides of grinding wheels unless they are the special wheels designed specifically for this purpose. 6. Use of any other accessory or attachment other than those specified might create a hazard for the operator. Ю" BENCH GRINDER Cat. No. 4330, TY. 1,115V, 1 Ph. Cat. No. 4330-01, TY. 1, 220V, 1 Ph. Cat. No. 4335, TY. 1, 220/440V, 3 Ph. 1 11467 5/16-24 x % Hex head screw (12) 2 393 5/16 Lock washer (12) 3 982372 Guard cover (2) 4 6947 5/16-24 x 1 Hex head screw (2) 5 982370 Wheel guard 6 13345 1/4 -28 x Vz Round head machine screw and washer (2) ...
Otros modelos de este manual:Máquinas de rectificar - 2928-1 (2.96 mb)
Máquinas de rectificar - 4330-01 (2.96 mb)
Máquinas de rectificar - 4335 (2.96 mb)