Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Dixon Tamaño del archivo: 1.6 mb Nombre del archivo: Idioma del manual:

Install the front and rear mount brackets to the deck with the pin and hairpin cotter supplied with the kit. 1. Make sure the tension release lever is forward or disengaged. 2. Place the belt over the pulley on the deck. Refer to illustration for proper routing. 3. Move the tension release lever to the rear and engage in the latch. 10 ASSEMBLY BELT COVER TAB 4 INSTALLING BELT COVERS RETAINER KNOB OUTER PULLEY COVER DECK BELT SHIELD MIDDLE CHUTE LATCH DECK BELT SHIELD WING NUT TAP SCREW BELT SHIELD STANDOFF 1. Place deck belt shield over spindle, aligning hole with bolt on belt shield standoff. 2. Attach with wing nut to standoff and use tap screw from kit to attach the other side of the belt shield to the deck. 3. Place retainer on the outer pulley cover. 4. Align the tab end of the belt cover into the slot on the deck belt shield and the other end over the end of the outer pulley cover. 5. Secure with knob. 11 ASSEMBLY 5INSTALLING MIDDLE CHUTE MIDDLE CHUTE BLOWER ASSEMBLY Depending on model, engine guard may have available mounting holes. If drilling is needed, use template supplied with kit. 1. Attach template to engine guard at the corresponding holes as shown in illustration. With centerpunch, transfer the four 1/8" bagger mount holes to the engine guard. 2. Remove template and drill four 11/32" holes in engine guard at locations marked in Step 2 . 6 INSTALLING BAGGER MOUNT 3 Bin Collector MOUNT STRAP MOUNT TUBE MOUNT STRAP RAM MOUNT 1/8" DIAMETER HOLES 3. Install the bagger mount tube from the mount kit. ENGINE GUARD 3. Remove the front carriage bolts securing the engine guard. 4. Install kit mount straps between the mount tube and frame as shown in the illustration. The front side of the kit mount straps should be on the inside of the mower frame. 5. Tighten all hardware. KIT MOUNT STRAP KIT MOUNT STRAP RAM ULTRA MOUNT 1. Place middle chute over the top end of the blower assembly. 2. Latch middle chute to blower assembly. TEMPLATE ATTACHMENT MOUNT TUBE 12 ASSEMBLY 7 INSTALLING CHUTE SUPPORT 3 Bin System only 1. Position upper chute support against bagger inlet, fl ush at outer edges. See Illlustration. 2. Using support as a template, drill two 3/8" holes into bagger hood. UPPER CHUTE SUPPORT BAGGER INLET NUT BAGGER HOOD FLAT WASHERS HEX BOLT FLEX TRIM 3. Secure upper chute support to hood with hex bolts, washers and nyloc nuts. 8 INSTALLING WEIGHT KITS 1. BOLT 2. BOLT WEIGHT BRACKET WEIGHT PLATES 1. Bolt weight plates to weight brackets using four 1." bolts and four nuts. 2. Slide both weight brackets over the front tube on the frame, positioning the assembly in the center of the frame. 3. Secure with four 2." bolts and four nuts. 2. BOLT NUT 3. BOLT WEIGHT BRACKET CAST WEIGHT 1. Bolt one cast weight and two weight brackets together using four 2." bolts and four nuts. 2. Slide both weight brackets over the front tube on the frame, positioning the assembly in the center of the frame. 3. Secure with four 3." bolts and four nuts. Units with cast weight FRONT TUBE Units with two or more weight plates RAM 44 RAM 50 FRONT TUBE ASSEMBLY 9 9 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY NOTE: For ease of assembly, you may wish assistance from another person for mounting the cover assembly to mower. 1. Position cover assembly on ground behind mower. CAUTION DO NOT operate mower with grass catcher, unless the front weights are installed. 2. Lift and rotate cover to align the cover brackets NOTE: with support assembly tubes. Ram Ultra units do not require a weight kit. 3. Slide the cover down over the support tubes until secure. COVER ASSEMBLY SUPPORT ASSEMBLY OPERATION TIPS FOR IMPROVED BAGGING OPERATION Follow the mower operation instructions in the mower operator’s manual. When utilizing the grass catcher on a lawn where grass and leaf bagging equipment has not been used, thatch and debris that has accumulated for long periods of time will be picked up. The amount collected and the total time of operation may be greater than experienced with regular use of the grass catcher. • Always run throttle at full speed when bagging. • Select a speed low enough to give good mower cutting performance, good quality cut and good bagging performance. NOTE: It may be necessary to overlap width of cut to suit your conditions. • If grass is extremely tall, it should be mowed twice. The first time relatively high, the second time to desired height. • Use left hand side of mower for trimming. • Plastic trash bags (3.0 mil, 30 gallon) can be inserted inside grass catcher containers for ease of debris disposal. To remove the plastic trash bags when full: a. Disengage blades, shift into neutral, engage the parking brake and stop the engine. b. Unlatch and raise cover. c. Remove one container at a time by grasping container handles and pulling toward the rear, off of the tube rails. d. With the container resting on the ground, close and secure the top of the plastic lawn bag. e. Tip the container on its side and slide the filled bag ...

Descargar ahora

Introduzca dos números de la imagen: