Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
It is extremely important to read and follow the instructions before attempting to use your crossbow. Serious injuries to yourself or others, damage to your crossbow or poor performance from your crossbow could result from failure to thoroughly read and understand these instructions. If any part of this manual is unclear to you contact the service department at 800-237-4507. After assembly of your crossbow, please keep manual for future reference. As with any other high performance equipment, meticulous care and a regular maintenance schedule must be maintained. Manual Contents Safety Guidelines 4 Parts Checklist 5 Specifications 5 Parts List (all Components) 6 Parts Picture 6 Assembly 7-9 Crossbow Operation 10-11 Trouble Shooting 12-13 Care and Maintenance 14 Warranty 15 Warranty Registration 16 3 Safety Guidelines For: RX150 The RX150 is equipped with an automatic safety, which engages every time the crossbow is cocked. The safety must be released before each shot. This, as with any other mechanical device does not guarantee total safety, as no safety device is a substitute for common sense and safe handling. NEVER pull the trigger on a crossbow when the safety is in the .safe. position or anywhere between .safe. and .fire.. Do not attempt to alter or modify the trigger mechanism, doing so will void your warranty and may cause personal injury to yourself or others. The following rules should be followed at all times: EXTREME CAUTION SHOULD BE USED AT ALL TIMES WHEN HANDLING A CROSSBOW. FAILURE TO FOLLOW THESE RULES COULD RESULT IN SERIOUS INJURY OR DEATH. ! Always keep your fingers below the flight track and out of the path of the strings when firing the crossbow. ! Never dry-fire the crossbow (shoot without an arrow). Dry firing will void the warranty and result in damage to the limb, cable and string, possibly causing personal injury. ! Never fire the crossbow until you are sure of your target. ! Always use an adequate target and backstop when target shooting. ! Always use suitable crossbow arrows, such as Barnett's 16" 2117 or 2216 Aluminum Crossbow Arrows. Arrows of improper stiffness or mass weight may damage the limb and cable assembly, voiding the warranty and possibly cause personal injury. ! Always inspect the crossbow and arrows before firing. Bent or damaged arrows are not safe to fire and should be discarded or repaired. 4 SPECIFICATIONS RX150 Feet Per Second 220 Power Stroke 16“ Draw Weight 150 Physical Weight 4 Width 25.6 Length 32.5 String Length 25.6 Number of Strands 32 String Stock # 16024 PARTS LIST FOR RX150 QUANTITY PART NAME 1 Pressure Plate 1 Nose Bolt 1 3mm Hex Nut 1 String 1 Cable Stringer 1 Adjustable Rear Blade Sight 1 Fixed Front Sight 1 Foot Stirrup 1 Lubewax 1 Stock Extender If you are missing any of the above parts or need information on older models, contact the Barnett Service department at 1-800-2374507. 5 BREAKDOWN OF CROSSBOW PARTS FOR RX150 1 BODY 2 FLIGHT TRACK 3 FOOT CLAW 4 FRONT SIGHT 5 PROD 6 NOCK ENDS ( needs to be riveted ) 7 NOSE BOLT 8 REAR ADJ SIGHT 9 PRESSURE PLATE WITH RUBBER PAD 10 STOCK EXTENSION 11 STOCK EXTENSION NUTS 12 STRING 13 STRINGER 14 TMB 15 TRIGGER MECH Make sure nose bolt is against metal part of the pressure plate. Pressure pad should be installed between prod and nose bolt. Make sure rubber pad is against the prod. 12 14 10,11 1 7 5 3 4 9 2 6 6 ASSEMBLY GUIDE RX150 Installing Prod Assembly Note: During prod assembly procedures, pay close attention to proper installation of pressure plate and rubber pad. Improper installation of these items will result in damage and void the warranty. 1. With 3mm hex key, back out nose bolt until it is flush with plastic. 2. Install pressure plate with metal surface facing forward so only the rubber contacts prod. 3. Slide in prod until arrow appears in inspection hole. The 3/16. hex wrench provided. 4. Once all these steps are completed, tighten up nose bolt securely with hex key. Attaching the Foot Stirrup Assembly 1. Remove the two front screws and loosen the back screws that hold the plates on the front sides of the gun body. 2. Line up holes in foot stirrup over front hexagon stud. Make sure foot stirrup is laying in the plastic grooves in the nose housing. 3. Vertically slide front sight over nose housing and into grooves. 4. Replace side plates. Make sure screws are tightened firmly. An incorrectly installed foot stirrup can cause serious bodily injury. Mounting the Front Sight for RX150 1. Remove front sight assembly from hardware package. 2. Place front sight into slots provided with the angle of front sight pointing towards the trigger. 3. Attach front sight with screws provided through holes in plate of nose unit. Tighten. 7 4. Place sight pin, thread down, through top of front sight. Attach circular nut. Rear Sight for RX150 The RX150 is equipped with an adjustable rear sight (Unless bow is shipped in a package or kit.) preinstalled at the factory. See Figure 1 Fig. 1 Installing Optional Scope If y...