Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther. • To change the deflector position, loosen knob, move deflector to desired position and tighten knob securely. HIGH POSITION CHUTE DEFLECTOR LOW POSITION KNOB FIG. 11 9 OPERATION TO THROW SNOW (See Fig. 12) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. • Release the auger control lever to stop throwing snow. FIG. 12 AUGER CONTROL LEVER USING THE CLEAN-OUT TOOL (See Fig. 13) In certain snow conditions, the discharge chute may become clogged with ice and snow. Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or in spect ing, make certain all controls are disengaged and the auger/ impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent accidental starting. • Release the auger control lever and shut off the engine. • Remove the clean-out tool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage. After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip. CLEAN-OUT TOOL FIG. 13 MOUNTING CLIP DISCHARGE CHUTE • Make sure the discharge chute is pointed in a safe direction (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting the engine. • Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger housing and the discharge chute. TO MOVE FORWARD AND BACKWARD (See Fig. 14) SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or reverse movement of the snow thrower. SPEED and DIRECTION are controlled by the drive speed control lever. • Press downward on the speed control lever and move lever to de sired po si tion BE FORE engaging the traction drive control lever. Be sure lever springs back and locks into desired position. CAUTION: Do not move speed con trol le ver when traction drive control lever is en gaged. Damage to the snow thrower can result. • Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower. NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process. DRIVE SPEED CONTROL LEVER TRACTION DRIVE CONTROL LEVER FIG. 14 10 OPERATION TO ADJUST SKID PLATES (See Fig. 15) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal con di tions, such as a paved driveway or side walk, place skid plates in the highest position (lowest scraper clear ance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven. NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property dam age or damage to the snow thrower. • If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clear ance) position. 1. Shut off engine and wait for all moving parts to stop. 2. Adjust skid plates by loosening the hex nuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely. SKID PLATE HEX NUTS HIGH POSITION (LOW GROUND CLEARANCE) AUGER HOUSING SCRAPER BAR LOW POSITION (HIGH GROUND CLEAR ANCE) FIG. 15 SCRAPER BAR (See Fig. 15) The scraper bar is not adjustable, but is reversible. After con sid er able use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a dam aged or worn scrap er bar. BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 16) The engine on your snow thrower has been shipped, from the factory, already filled with oil. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe ...
Otros modelos de este manual:Quitanieves - SNOW THROWER XT824ES (3.01 mb)