Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
With chute rotator head and chute bracket aligned, spring. po si tion chute rotator head on pin and threaded stud of mounting bracket. 4. Install 3/8 washer and locknut on threaded stud and tighten securely. AUGER CONTROL ROD CONTROL ARM VINYL SLEEVE LOOP OPENING UP CHUTE ROTATOR HEAD 3/8 WASHER 3/8 LOCKNUT THREADED STUD PIN ROTATOR HEAD MOUNT ING BRACKET CHUTE BRACKET FIG. 7 ALIGN BEFORE TIGHTENING LOCKNUT FIG. 5 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the factory for shipping purposes. Correct and equal tire pres sure is important for best snow throwing performance. • Reduce tire pressure to 14-17 PSI. AUGER CONTROL LEVER AUGER CONTROL ROD AUGER CONTROL BRACKET RETAINER SPRING FIG. 6 6 OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT. FORWARD REVERSE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. IGNITION KEY. INSERT TO START AND RUN, PULL OUT TO STOP. DISENGAGED ENGAGED SNOW TRACTION DISCHARGE DRIVE CONTROL 7 8 OPERATION Drive speed control lever - used to select forward or reverse motion and speed of snow thrower. Traction drive control lever - used to engage powerpro pelled for ward or reverse motion of snow thrower. Auger control lever - used to engage auger motion (throw snow). Discharge chute control lever - used to change the di rection the snow is thrown. Skid plate - used to adjust height of scraper bar from the ground. Toolbox - used to store spare shear bolts, locknuts and wrench. Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use. Electric start button - used for starting the engine. Recoil (auxiliary) starter handle - used for start ing the en gine. Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine. Choke control - used for starting a cold engine. ON / OFF switch - used to STOP the engine. MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. TRACTION DRIVE CONTROL LEVER DISCHARGE CHUTE CONTROL LEVER DRIVE SPEED CON TROL LEVER AUGER CONTROL LEVER MUF FLER TOOLBOX HANDLE KNOB LIGHT CHUTE DE FLEC TOR DISCHARGE CHUTE AU GERS NOTE: ITEMS ABOVE ARE SHOWN IN THEIR TYPICAL LOCATION ON THE ENGINE. ACTUAL LOCATION MAY VARY WITH THE ENGINE ON YOUR UNIT. FIG. 8 CLEAN-OUT TOOL SKID PLATE MUF FLER GAS O LINE FILLER CAP SAFETY IGNITION KEY CHOKE CONTROL PRIM ER RECOIL (AUXILIARY) STARTER HANDLE ELECTRIC START BUTTON ON / OFF SWITCH CHUTE DE FLEC TOR KNOB OPERATION 00155 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE YOUR SNOW THROWER Know how to operate all controls before adding fuel or attempting to start the engine. STOPPING TRACTION DRIVE • Release traction drive control lever to stop the forward or reverse movement of the snow thrower. AUGER • Release the auger control lever to stop throwing snow. ENGINE 1. Move ON / OFF switch to “OFF” position. 2. Remove (do not turn) safety ignition key to prevent unauthorized use. NOTE: Never use choke to stop engine. TO USE CHOKE CON TROL (See Fig. 9) The choke con trol is located on the en gine. Use the choke control when ev er you are starting a cold en gine. Do not use to start a warm en gine. • To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage. FULLOFF FIG. 9 TO CONTROL SNOW DISCHARGE (See Figs. 10 & 11) WARNING: Snow throwers have exposed rotating parts, which can cause severe injury from contact, or from material thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup. WARNING: If the discharge chute or au ger become clogged, shut-off en gine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to un clog the chute and/or auger. The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever. • To change the discharge chute position, press down ward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position. DISCHARGE CHUTE CONTROL LEVER FIG. 10 The DISTANCE that snow is thrown is controlled by the position of the chute deflector. ...
Otros modelos de este manual:Quitanieves - SNOW THROWER XT824ES (3.01 mb)