Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
Attach the support clamp (C, Figure 2) and hook assembly (B) to the hitch. Secure with four 5/16-18 x 1 carriage bolts (A), washers (D), lockwashers (E), and nuts (F). Do not tighten the hardware at this time. Figure 2. Install Support Clamp A. 5/16-18 x 1 Carriage Bolt D. 11/32 Washer B. Hook Assembly E. 5/16 Lockwasher C. Support Clamp F. 5/16-18 Nut B C D E A F Conquest / 1700 / 2700 & Prestige / 1800 / 2800 Series B C D E A F Broadmoor / 1600 / 2600 Series Assemble Push Bar Latch 1. Attach Push Bar Latch (B, Figure 3), to hitch. Secure with four .31-16 x 1 bolts (A), and four .38-16 flange nuts (C). Two Wheel A B C Four Wheel Drive Models Drive Models Figure 3. Assemble Push Bar Latch A. Bolt, .38-16 x 1 C. Flange Nut, .38-16 B. Push Bar Latch BC D B A Figure 4. Assemble Lift Rod A. Lift RodC. Spring B. Set CollarD. Rod Guide A B Figure 5. Early/Later Lift Links A. Early Model Lift Link B. Later Model Lift Link Assemble Lift Rod 1. Install the set collars (B, Figure 4), spring (C), and rod guide (D) on the lift rod (A) as shown. Final adjustment of the set collars will be made after the hitch and attachment are installed. 4 Sub-Frame Hitch Installation Instructions INITIAL INSTALLATION Manual Lift Models LIFT LINK - EARLY VS. LATER The early model lift link (A, Figure 5) was used on early production Conquest/1700/2700 Series tractors. It must be replaced with the later model lift link (B) included with this attachment. The later model link works in all applications. Discard the early model link (A). LIFT LINK POSITION The lift link is installed differently depending on what attachment is being used. Refer to Figure 6 for link installation information. Hydraulic Lift Models 1. Fully lower the hydraulic lift. The lift assembly is spring loaded so it will need to be held in the down position to perform of the following procedures. 2. Remove and retain the flat head pin (B, Figure 7) and hair pin clip (E) securing the lift cylinder (A) to the lift shaft assembly (F). Remove and retain the flat washers. 3. Mount the lock plate (D) next to the cams on the lift shaft assembly (F) as shown. 4. Install the original flat head pin (B) and new flat head pin (C) and secure with hair pin clips. A B C D E A F C D G Snowthrower & Dozer Applications Mower Applications Figure 6. Connect Lift Link A. Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E. Upper Hole (Snowthrower Applications) F. Slot of Lift Link (Mower Applications) G. Lower Hole (Mower Applications) A B C D F E Figure 7. Install Lock Plate - Hydraulic Lift Models A. Lift Cylinder D. Lock Plate B. Flat Head Pin (Original) E. Hair Pin Clips C. Flat Head Pin (New) F. Lift Shaft Assy. 5 6 Installation Instructions Sub-Frame Hitch A C D E B Figure 8. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E. Clamp Plate C. Hitch Rod Install Hitch 1. Slide the hitch under the tractor. 2. Raise the rear of the hitch and place the hook (C) over the lift shaft. 3. Connect the front...
Otros modelos de este manual:Quitanieves - 1600 (719.25 kb)
Quitanieves - 1800 (719.25 kb)
Quitanieves - 2800 (719.25 kb)