Votos - 5, Puntuación media: 3.8 ( )

Fabricar: Ariens Tamaño del archivo: 7.4 mb Nombre del archivo: Idioma del manual:

IMPORTANT: Gradually open choke after engine starts. 1 OS1332 GB - 14 GB - 15 Throttle The throttle controls the engine speed. To increase or decrease the engine speed, adjust to: 1. Fast (normal or warm starts) 2. Part-Throttle 3. Slow (cold weather starts) 4. Stop (engine is off) (Not on 12V models) Electric Starter (120V electric start models) The electric starter will start a properly choked and cranked engine when the key is turned (12V) or starter button (120V or 240V) is pushed. Refer to Starting and Shut Off on page 17. Recoil Starter Handle When pulled, handle will turn engine over. IMPORTANT: DO NOT let handle snap back against starter. Snow Clean-Out Tool (Figure 11) To clear the chute: 1. Shut off the engine. 2. Wait 10 seconds and make sure impeller blades have stopped rotating. 3. Remove the snow clean-out tool (1) from the auger housing and use it to remove the clog. 4. Replace the snow clean-out tool on the auger housing. Deflector Remote Place deflector into position before operation. DO NOT throw snow any higher than necessary. Place deflector remote in a forward notch to throw snow lower. Place deflector remote in a rearward notch to throw snow higher. Discharge Chute Discharge chute rotates 200°. ALWAYS position discharge chute in safe direction and angle, away from operator and bystanders, before starting engine. Discharge Chute Control IMPORTANT: If chute does not stay in set position, adjust as directed in SERVICE AND ADJUSTMENTS on page 22, or repair before operation. Rotate the Chute with Discharge Chute Control. IMPORTANT: DO NOT force frozen chute controls. If still frozen, take to warm place until controls are free. Heated Handles (926002, 003, 004, 005, 006, 102, 103, 300, 301, 302, 303, 304, 500, 501) Turn the heated handles switch to the ON (1) position to activate. Turn the switch to the OFF (2) position to deactivate. Remote Differential (926004, 005, 006, 300, 301, 500, 501) Squeeze and hold the remote differential lever to lock differential so both wheels drive and provide better traction. Release the remote differential lever to allow easier steering. If remote differential does not engage or disengage properly, adjust or repair before operation (see REMOTE DIFFERENTIAL (926004, 005, 006, 300, 301, 500, 501) on page 23). Remote Wheel Lock (926002, 003, 102, 103, 302, 303, 304) Squeeze and release the remote wheel lock to lock the left wheel for better traction when throwing snow or to unlock the left wheel for easier steering. NOTE: The wheel lock will not release when under load. Do not unlock the wheel while turning. If the wheel lock will not release, turn the unit slightly left or right to relieve axle load and release the axle lock. WARNING: Hand contact with the rotating impeller is the most common cause of injury associated with snow throwers. Never use your hand to clean out the discharge chute. 1 2 3 4 OL2720 1 Figure 11 OS7100 Figure 12 OS7105 OS1950 1 2 GB - 16 If remote wheel lock does not lock or unlock properly, adjust or repair before operation (see REMOTE WHEEL LOCK (926002, 003, 102, 103, 302, 303, 304) on page 23). Axle Lock Pin (Figure 13) (926001, 101, 504, 505) Use the axle lock pin to lock or unlock the right or left wheel. Lock both wheels to increase traction; unlock one wheel to allow for easier turning of the unit. NOTE: Unit will not drive with both wheels unlocked. Scraper Blade The scraper blade allows the back of the housing to keep better contact with the surface being cleared. It also prevents damage to the housing from normal wear. IMPORTANT: DO NOT allow Scraper Blade to wear too far or Auger/Impeller housing will become damaged. Runners The runners control the distance between the scraper blade and the ground. Adjust runners equally to keep blade level with the ground. Refer to Pre-Start on page 17 for recommended settings. Drift Cutters (Figure 14) Drift cutters break up snow drifts that are taller than the auger housing and direct the snow into the auger. Store the drift cutters on the auger housing when not in use. Install them as shown below so they are taller than the snow to be cleared. FILLING FUEL TANK Fuel Shut-Off Valve IMPORTANT: The fuel shut-off valve MUST be in the closed position prior to transporting the unit. The fuel shut-off valve has two positions: • Closed Position: Use this position to service, transport, or store the unit. • Open Position: Use this position to run the unit. To add fuel to fuel tank: 1. ALWAYS place unit in open or well-ventilated area. 2. Stop engine and allow to cool. 3. Clean Fuel Cap and surrounding area to prevent dirt from entering Fuel Tank. 4. Remove Cap. Figure 13 Wheel Unlocked Wheel Locked Axle Lock Pin WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. Figure 14 1.Stored Position 2.Operating Position 1 2 OS7110 Figure 15 CLOSED OPEN OS7115 IMPORTANT: DO NOT use gasohol or gasoline containing alcohol. See Engine Manual for correct type and grade of fue...

Descargar ahora

Introduzca dos números de la imagen: