Iniciar sesión:
Votos - 1, Puntuación media: 3 ( )

Manual de usuario Craftsman, modelo 1693134

Fabricar: Craftsman
Tamaño del archivo: 3.31 mb
Nombre del archivo:
Idioma del manual:
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Always remove the ignition key, disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine. Troubleshooting, Adjustment & Service TRACTOR TROUBLESHOOTING CONTINUED PROBLEM CAUSE REMEDY Brake will not hold. 1. Brake is incorrectly adjusted. See Brake Adjustment. 2. Brake worn out See your dealer Tractor steers hard. 1. Power steering Malfunction See your dealer. 2. Improper tire inflation. Check and correct. 3. Spindle bearings dry. Grease spindles. See Lubrication. Low Oil Pressure Light is On 1. The engine oil pressure light may Light should go out immediately. If the light go on when the engine is first stays lit, contact your dealer. started; this is normal. Irregular Voltage Light is On. 1. Battery discharged. Recharge or replace battery. Or Volt Meter Indicates Irregular 2. Charging system malfunctioning. See you dealer. Voltage Level Differential Lock Won’t Engage 1. Differential lock cable See your dealer. out of adjustment. Cruise Control Won’t 1. Cruise lever tension See your dealer. Stay Engaged out of adjustment. 2 Speed Control Won’t Shift 1. Operator Error. See Operation Section. 2. Transmission Failure. See Your Dealer. Troubleshooting the Mower PROBLEM CAUSE REMEDY Mower will not raise. 1. Lift chains not properly attached Attach or repair. or damaged. Mower cut is uneven. 1. Mower not leveled properly. See Mower Adjustment. 2. Tractor tires not inflated See Maintenance Section. equally or properly. 3. Attachment lift not fully lowered. Fully lower attachment lift. Mower cut is rough looking. 1. Engine speed too slow. Set to full throttle. 2. Ground speed too fast. Slow down. 3. Blades are dull. Sharpen or replace blades. (See Mower Blade Service.) 4. Mower drive belt slipping Clean or replace belt as necessary. because it is oily or worn. 5. Check PTO (Electric Clutch) See Adjustments Section. Adjustment. 6. Blades not properly fastened See Servicing the Mower Blades. to arbors. 6. Attachment lift not fully lowered. Fully lower attachment lift. Engine stalls easily with 1. Engine speed too slow. Set to full throttle. mower engaged. 2. Ground speed too fast. Slow down. 3. Carburetor improperly adjusted. See Engine Manual. 4. Cutting height set too low. Cut tall grass at maximum cutting height during first pass. 5. Discharge chute jamming Cut grass with discharge pointing toward with cut grass. previously cut area. Raise cutting height. Excessive mower vibration. 1. Blade mounting screws Tighten to 45-55 ft.lbs. (61-75 N.m.). are loose. 2. Mower blades, arbors, Check and replace as necessary. or pulleys are bent. 3. Mower blades are out Remove, sharpen, and balance blades. of balance. See Servicing the Mower Blades. 4. Belt installed incorrectly. Reinstall Correctly. Excessive belt wear or breakage. 1. Bent or rough pulleys. Repair...

Otros modelos de este manual:
Quitanieves - 1692871 (3.31 mb)
Quitanieves - 1692870 (3.31 mb)
Quitanieves - 1692872 (3.31 mb)
Quitanieves - 1693112 (3.31 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría