Iniciar sesión:
Votos - 1, Puntuación media: 4 ( )

Manual de usuario Craftsman, modelo 1693130

Fabricar: Craftsman
Tamaño del archivo: 3.31 mb
Nombre del archivo:
Idioma del manual:
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Install Quick Connector Covers 16 MOWER DECK REMOVAL & INSTALLATION NOTE: Perform mower removal and installation on a hard, level surface such as a concrete floor. Removing the Mower Deck 1. Start the engine 2. Set the mower cutting height to minimum. 3. Fully raise the attachment lift. 4. Stop the engine. 48” AND 60” MOWERS 5. Pivot the two front gauge wheels from mowing position to sliding position by pushing down on the top of the spindle and pivoting the wheel (see Figure 12). 54” MOWERS 5. Remove the hair pin clip, push down on the top of the spindle, and rotate the gauge wheel into sliding position (see Figure 12). Replace the hair pin clip. ALL MODELS 6. Move the left rear slide wheel into slide position (see Figure 13). 7. Start the engine. 8. Fully lower the attachment lift. 9. Set the cutting height to maximum. 10. Stop the engine. 11. Unhook the two lift chains from the tractor lift arms. 12. Turn the ignition switch to RUN position, and set the mower cutting height to minimum (it is not necessary to start the engine). 13. Turn the ignition switch to the OFF position. 14. Disconnect the electrical connection from the tractor and recap the tractor electrical socket. See Figure 15. 15. Remove the long hitch pin (B, Figure 16) and safety clip connecting the hitch bucket (A) to the mower deck. 16. Remove the two small pins (C, Figure 16) connecting the hitch bucket (A) to the tractor. 17. Remove the hitch bucket (A, Figure 16) from the mower deck. 18. Remove the drive shaft (D, Figure 16) by pulling back the locking collar (A, Figure 17) and pulling the shaft off the PTO. Operating the Tractor WARNING Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower. Figure 12. Pivoting the Gauge Wheels Figure 13. Rear Slide Wheel - 48” & 60” Mowers A. Clevis Pin C. Slide Wheel Arm B. Hair Pin Clip Figure 14. Mower Lift Chains A. Lift Chains A C B A 19. Slide the deck out from under tractor. 54” Mower 48” Mower & 60” Mower Operating the Tractor Installing the Mower Deck 1. Raise the attachment lift and slide the mower under the tractor. 2. Hook up the electrical connection (Figure 15). 3. Start the engine. 4. Set the cutting height to maximum. 5. Fully lower the attachment lift. 6. Shut off the engine. 7. Make sure the mower lift chains are directly below the lift arms. Attach the 2 mower lift chains to the tractor lift arms (Figure 14). 8. Turn the ignition switch to the RUN position, and set the mower cutting height to minimum (it is not necessary to start the engine). 9. Turn the ignition switch to the OFF position. 10. Mount the hitch bucket (A, Figure 16) to the deck. 11. Attach the hitch bucket to the tractor using the two short pins (C, Figure 16) and safety clips. 12. Attach the hitch bucket (A, Figure 16) to the mower deck using the one long pin (B) and safety clip. 13. Start the engine. 14. Fully raise th...

Otros modelos de este manual:
Quitanieves - 1692871 (3.31 mb)
Quitanieves - 1692870 (3.31 mb)
Quitanieves - 1692872 (3.31 mb)
Quitanieves - 1693112 (3.31 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría