Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you. Avoid any areas that expose enclosed or activities you to carbon monoxide. STARTING THE ENGINE 1. Move the shift lever to “N” (Neutral) position. i I I N (Neutral) OPERATION 2. Set the transmission release lever ENGAGED in the ENGAGED position (page 16). TRANSMISSIONRELEASE LEVER 3. Turn the fuel valveto the ON position. Besurethatthedrainknobis tightened securely. \ DRAIN KNOB THROlTLE LEVE 4. In coldweather and when the engine is cold, follow the procedures below. HS624/HS724/HS828/HS928: Move the throttle lever to the CHOKE position. / CHOKE OPERATION HS1132: Pull the choke knob to the CLOSED position and move the throttle lever to the FAST position. CHOKE KNOB eCLOSED THROTTLE LEVER 5. Start the engine. Electric-start Models (TAS, WAS type): a. Connect your power cord to the switch box and the male end of the power cord to a properly grounded 120 volt ac outlet. I ACAUTION I IUSE ONLY WITH GROUNOEO OUTLET AN0 3-WIRE CORD. 1120 VOLT A.C. ONLY 100 NOT CRANK OVER 1 MINUTEWllHOLlT COOLING 15 MINUTES. 100 NOT USE INRAIN. I POWER CORD To minimize the possibility of potentially dangerous electrical shocks, always use a 3-conductor power cord with a power rating of no less than 15 amps. Also, be sure that the outlet you are using is properly grounded. Do not connect and disconnect the power cord with wet hands. Be sure to hold the plug when disconnecting the power cord from the electrical outlet or switch box. Do not disconnect by pulling on the power cord. OPERATION b. Turn the engineswitch to the ON position. ON I I\I c. Push the starter button until the engine starts. After the engine starts, disconnect the power from cord the electrical outlet, and then from the switch box. Do not operate the starter for more than 1 minute. If the engine fails to start, release the button and allow the starter to cool for 15 minutes before operating it again. Manual Starting only a. Pull the starter grip lightly until you feel resistance, then pull briskly. b. Return the starter grip gently to the engine. piEq Do not allow the startergrip to snap back against the engine. Return it gently to prevent damage to the starter. Do not pull the starter grip while the engine is running. The starter could be damaged. OPERATION 3. Let the engine warm up for several minutes. HS624/HS724/HS828/HS928: If the throttle lever has been movedto the CHOKE position, gradually move the throttle lever to the SLOW position as the enginewarms up. HS1132: If the choke knob has been pulled to the CLOSED position to start the engine, gradually push it to the OPEN position as the engine warms up. Move the throttle lever to the SLOW position. CHOKETHROTTLE LEVER KNOB OPEN 1, OPERATION 4. While warming the engine up, also warm the transmission as follows: a. Check that the shift lever is in the “N” (Neutral) position. i I N(Neutra1) I / / SHIFT LEVER . DRIVE CLUTCH LEVER b. Squeeze the drive clutch lever for about 30 seconds to warm up the transmission fluid. STOPPING THE ENGINE To stop the engine in an emergency, simply turn the engine switch to the OFF position, Under normal conditions, use the following procedure. OPERATION 1. Release ReleaseRelease the thethe auger augerauger and andand drive drivedrive clutch clutchclutch levers. levers.levers. The TheThe drive drivedrive and andand snow snowsnow blowing mechanism mechanismmechanism will willwill stop stopstop operation. operation.operation. DRIVE DRIVEDRIVE CLUTCH \ LEVER 2. Move the shift lever to “N” (Neutral) position. i I I N(Neutra1) 3. Turn the throttle lever to the SLOW position. HS624lHS724IHS828lHS928 HS1132 I THROTTLE LEVER OPERATION 4. Turn the engine switch to the OFF position. 5. Turn the fuel valve to the OFF position. FUEL VALVE \ 28 OPERATION CLEARING SNOW 1. Move the throttle lever to the FAST position for normal operation. R (Reverse) N (Neutral) 2. Release the auger clutch i lever, and move the shift lever to select the desired drive speed. Low speed is recommended for removing deep or hardpacked snow. 3. Set the foot pedal to the correct position (page 14, track type only). 4. Adjust the throwing direction by using the chute crank and the discharge deflector lever (page 12 and 14). 5. Squeeze the auger clutch lever The machine will clear snow when you squeeze the auger clutch lever. OPERATION 6. Squeeze the drive clutch lever to self-propel the snowblower. Ifthe transmission release lever (page22) is in the ENGAGEDposition, and the shift lever (page 29) is in the FORWARD (F) position, the hydrostatic drive will DroDel the snowblower forward when you -~ -~ I, squeeze the drive clutch lever. RIVE CLUTCH LEVER To move from one place to another, or to change direction, use the drive clutch lever only. Releaseboth the drive clutch lever and auger clutch lever, and then squeeze the drive clutch lever. \ DRIVE CLUTCH LEVER OPERATION 7. Release the clutch levers to stop clearing or moving. DRIVE OPER...
Otros modelos de este manual:Quitanieves - HS724 (1.49 mb)
Quitanieves - HS928 (1.49 mb)