Votos - 4, Puntuación media: 4.5
(
)
)
|
Resumen del manual
The DIRECTION in which snow isto be thrown is controlled by the discharge chute control lever. • To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position. The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther. Press downward on chute deflector control lever and move lever forward to lower the deflector and decrease the distance. Move lever back to raise the deflector and increase the distance. Be sure lever springs back and locks into desired _osition. DISCHARGE CHUTE CONTROLLEVER CHUTE DEFLECTOR REMOTE LEVER FIG. 13 TO THROW SNOW (See Fig. 14) The auger rotation is controlled by the auger control lever located on the right side handle. • Squeeze auger control lever to handle to engage the auger and throw snow. Release the auger control lever to stop throwing snow. AUGER CONTROL LEVER FIG, 12 FIG. 14 11 OPERATION USING THE CLEAN=OUT TOOL (See Fig. 15) In certain snow conditions, the discharge chute may become clogged with ice and snow. Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or inspecting, make certain all controls are disengaged and the au= get/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent ac= cidental starting. • Release the auger control lever and shut offthe engine. • Remove the clean-out tool from it'smounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage. After the packed snow has been dislodged, return the clean- out tool to it's mounting clip by pushing it into the clip. • Make sure the discharge chute is pointed inasafe direction (no vehicles, buildings, people, or other objects are inthe direction of discharge) before restarting the engine. • Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger housing and the discharge chute. DISCHARGE CHUTE /[_ TOOL FIG. 15 TO MOVE FORWARD AND BACKWARD (See Fig. 16) SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to engage the drive system. • Release traction drive control lever to stop the forward or reverse movement of the snow thrower. SPEED and DIRECTION are controlled by the drive speed control lever. Press downward on the speed control lever and move lever to desired position BEFORE engaging the traction drive control lever. Be sure lever springs back and locks into desired position. Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the operation of the snow thrower. NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever inthe engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process. TRACTION DRIVE LEVER DRaVE SPEED CONTROLLEVER FIG. 16 POWER STEERING OPERATION (See Fig. 17) Steering triggers are used to assist in steering your snow thrower. The triggers are located on the underside of each handle. When a trigger is squeezed, it disengages the drive wheel on that side of snow thrower and allows it to turn in that direction. • To turn left -squeeze left side trigger. • To turn right -squeeze right side trigger. LH TURN RH TURN TRIGGER TRIGGER FIG. 17 CAUTION: Do not move speed control lever when traction drive control lever is engaged. Damage to the snow thrower can result. 12 OPERATION TO ADJUST SKID PLATES (See Fig. 18) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven. NOTE: It is not recommended to operate the snow thrower over gravel or rocky surfaces. Objects such as gravel, rocks or other debris, can easily be picked up and thrown by the impeller, which can cause serious personal injury, property damage or damage to the snow thrower. • If snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest ...