Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Be thoroughly familiar with the controls and proper use of the equipment. Know how to stop the unit and disengage the controls quickly. •Never allow children to operate the machine. Do not allow adults to operate it without proper instruction. •Keep the area of operation clear of all persons, particularly small children and pets. • Do not carry passengers. • Make sure: a. tractor and attachments are in good operating condition. b. all safety devices and shields are in place c. and in good working condition, and d. all adjustments (skid shoe height, etc.) have been made. Preparation •Handle gasoline with care — it is highly flammable. a. Use only an approved gasoline container. b. Never remove the cap of the fuel tank or add gasoline to a running or hot engine, or fill the fuel tank indoors. Wipe up spilled gasoline. • Do not run the engine indoors. Exhaust fumes are dangerous. •Shift into neutral before attempting to start the engine. •Wear proper footwear. Do not operate tractor when barefoot or when wearing open sandals or canvas shoes. Operation • Do not allow anyone to use the snow plow/dozer blade unless they have been instructed on how to operate it safely. • Never attempt to adjust, repair or service the snow plow/dozer blade while the tractor engine is running. • Do not allow others near the snow/dozer blade while it is being used. • Use the snow plow/dozer blade only in daylight, or good artificial light. •Always lower the snow plow/dozer blade completely to the ground when leaving it unattended to prevent it from being accidentally lowered and causing injury. Make sure blade is locked in “DOWN” position due to spring-assist. •Always operate the tractor at reasonable speeds to prevent the blade from catching an object and stopping the tractor abruptly. 2 -Assemblies Regent/2500/500, Broadmoor/LT/2600/1600, & Landlord/GT/2700/1700 Series Parts Figure 1. Mfg. No. 1691520 Snow/Dozer Blade Assembly A. Blade Assembly B. I.D. Plate C. Hex Nut, 5/16-18 (4) D. Eyebolt (2) E. Tension Spring (2) F. Pivot Frame Assembly G. Hex Lock Nut, 1/2-13 (2) H. Spacer (2) I. Hex Capscrew, 1/2-13 x 1 (2) J. Shoe Assembly (2) K. Plain Washer, 3/8 (4) L. Lockwasher, 3/8 (10) M. Hex Head Capscrew, 3/8-16 x 3/4 (4) N. Wear Plate O. Hex Nut, 3/8-16 P. Carriage Bolt, 3/8-16 x 1 3 Assembles- Broadmoor/LT/2600/1600, & Landlord/GT/2700/1700 Series Parts Figure 2. Mfg. No. 1692039 Push Bar & Lift Rod Assembly A. Set Collar (Qty. 2) B. Setscrew, 5/16 x 1/2 (Qty. 2) C. Rod Guide Assembly D. Spring E. Lift Rod, (Manual or Electric Lift) F. Clip, Spring (Qty. 3) G. King Pin H. Push Bar Assembly I. Safety Clip (Qty. 2) J. Pivot Pin K. Latch Rod (Qty. 4) L. Hex Capscrew, 5/16-18 x 1 M. Lockwasher, 5/16 N. Full Hex Nut, 5/16-18 O. Hitch Pin P. Plain Washer, 5/16 (Qty. 2) Q. Chain R. Spring S. Spring Anchor Bracket T. Bar Stop (Qty. 2) U. Taptite Screw, 5/16-18 x 1 V. Lift Extension Lever W. Clevis Pin X. Spring Clip 4 Assemblies Regent/2500/500 Series Parts A. Set Collar (Qty. 2) B. Setscrew, 5/16 x 2 (Qty. 2) C. Rod Guide Assembly D. Spring E. Lift Rod F. Spring Clip (Qty. 3) G. Clevis Pin, 3/8 (Qty. 2) H. Push Bar Assembly I. Hitch Pin J. Plain Washer 5/16 K. Safety Clip L. Chain M. Spring N. Pivot Pin 5 Assemblies - Regent/2500/500 Series Parts A. Hitch Assy. B. Rear Support Assy. C. Washers (Qty. 2) D. Hairpin Clip (Qty. 2) E. Pin F. Spring Clip (Qty. 4) G. Clevis Pin, 3/8 (Qty. 2) H. Rod I. Spring Assist Bracket J. Capscrew, 3/8-16 x 2 K. Spacer, 25/64 x 5/8 x 17/64 L. Spacer, 13/32 x 1 x 13/16 M. Nut, Whizlock, 3/8-16 N. Lockwasher, 1/2 O. Hex Nut, 1/2-13 P. Capscrew, 1/2-13 x 1-1/4 6 Assembly All Models 1. Place the blade on a flat surface. 2. Regent/2500/500 & Broadmoor/LT/2600/1600 Series: See Figure 4. Install one bar stop (A) using the two 5/16-18 x 1 taptite screws (B). Do not install second bar stop. Landlord/GT/2700/1700 Series: Do not install bar stops. 3. See Figure 5. Insert threaded end of eyebolt (A) thru lug on blade, and screw on 5/16 nut (B) just far enough so that it is flush with the end of the eyebolt. 4. See Figure 5. Hook the springs (C) into the pivot frame (D). Using a pliers, stretch the springs to hook the opposite ends to the eyebolts (A). 5. See Figure 5. Tighten the nut (B) on each eyebolt enough to expose about 3/4“ (19 mm) of thread. 6. See Figure 5. Holding the first nut (B) with a wrench,add a second nut (E) to each eyebolt, and tighten securely against the first nut to act as a jam nut. A. Bar Stop B. Taptite Screw, 5/16-18 x 1 A. Eyebolt D. Pivot Frame B. Nut, 5/16 E. Nut, 5/16 C. Spring 7 Assembly NOTE: On single cylinder tractors, clevis pin (B, Figure 6) must be installed to bracket before mounting bracket on tractor frame. NOTE: Spring-assist bracket (A, Figure 6) does not need to be installed on units with electric lift. Broadmooi7LT2600/1600 Series & Landlord/GT/2700/1700 Series Only: 7...