7 OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFORE US

Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. • Empty the fuel tank by starting the engine and letting it run until the fuel lines and car bu re tor are empty. • Never use engine or carburetor cleaner prod ucts in the fuel tank or permanent damage may occur. • Use fresh fuel next season. NOTE: Fuel stabilizer is an

While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating po si tion and hold the snow thrower han dles. Serious personal injury and/ or damage to the unit could occur if the snow thrower should fall during the belt chang ing process. 1. REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, outdoors, away from fire or flame. Wipe up any spilled gasoline. 2. REMOVE DISCHARGE CHUTE - Loosen locknut se cu

2. Put the chute crank rod through the bracket on the lower handlebar. (See Figure 3) 3. Install the chute crank rod onto the shaft. 4. Fasten the chute crank rod with the screw and nut that were removed in step 1. Figure 2 Shaft Chute Crank Rod Nut Screw 1740274 10 ASSEMBLY 1740274 11 HOW TO ASSEMBLE THE HANDLE 1. Remove the packing material from the upper and lower handles. 2. Loosen the knobs on each side of the handle. (See Figure 3) 3. Raise the upper handle to the operating position (see F

This book contains important information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT PARTS and the WARRANTIES. This information must be included to make sure state laws and other laws are followed. PRODUCT INFORMATION 1740274 TP 100-4350-01-SW-R INTRODUCTION Congratulations on your purchase. This Snowthrower has been designed, engineered and

Before you start the engine, read this book. A WARNING: Before you make an inspection, adjustment (except carburetor), or repair, disconnect the wire from the spark plug. EMISSIONS CONTROL Maintenance, replacement, or repair of the emissions control devices and systems may be performed by any non-road engine repair establishment or indiv-However, to obtain a "no charge" emissions control service, the work must be performed by a factory authorized dealer. See the Emissions Warranty. GENERAL R

Guide the snowthrower by moving the handle (10) either left or right. Do not attempt to push the snowthrower. 3. To stop, release the auger drive lever (4). NOTE: If the auger continues to rotate, see "How To Adjust The Auger Control Cable” in the Maintenance section. 1741506 15 OPERATION BEFORE STARTING THE ENGINE 1. Before you service or start the engine, familiarize yourself with the snow thrower. Be sure you understand the function and location of all controls. 2. Make sure that all

• Presionar hacia abajo la palanca del mando de la velocidad y mover la palanca hasta la posicion deseada ANTES de conectar la palanca del mando de guia de traccion Asegurarse de que la palanca vuelva en su lugar y se fije en la posicion deseada. PRECAUCION: No mover la palanca del mando de la velocidad cuando la palanca del mando de la guia de traccion esta conectada. Esto puede perjudicar al motor y/o a la maquina quitanieves. • Velocidades mas lentas son para nieve mas pesada y velocidades ma

En el manual y en la maquina hay simbolos de advertencia. Si alguno de estos simbolos se ha deformado o desgastado, debe sustituirse por uno nuevo lo antes posible. Tengase en cuenta que tambien hay simbolos de advertencia fundidos en algunas piezas de la maquina. 545154658 Rev. 2 7/10/07 El soplador de hojas se utiliza para limpiar el suelo de hojas y escombros, soplando. Durante el trabajo, el operario debe estar afirmado en el suelo. El periodo de conformidad de las emisiones referido en la e