PRACTICES AND LAWS Practice usual and customary safe working precautions, for the benefit of yourself and others. Understand and follow all safety messages. Be alert to unsafe conditions and the possibility of minor, moderate, or serious injury or death. Learn applicable rules and laws in your area. Always follow the practices set forth in this manual. REQUIRED OPERATOR TRAINING Original purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by so

GEAR) Remove auger/impeller and gear case from housing referring to Auger/Impeller Section. Remove four bolts from bearing flange (Figure 22). Remove flange and gasket. NOTE: At this point bronze gear cannot be removed. Using bearing adjustment wrench remove adjustment plug. While holding input shaft in one hand and using a mallet, strike case until bearing cone pops out of the case. Bronze gear can then be removed from case. After bronze gear is removed, input shaft can then be removed. NOTE: I

Follow with Milk of Magnesia, beaten egg or vegetable oil. Get medical attention immediately! • In case of internal contact, DO NOT induce vomiting! Before tipping unit up onto housing, remove fuel so no spills will occur and remove battery. Ensure unit is secure and will not tip over during maintenance. ALWAYS keep protective structures, guards, and panels in good repair, in place and securely fastened. NEVER modify or remove safety devices. DO NOT change engine governor settings or over-speed

(cm) 16 (40.6) Speed - RPM- Max (min-1) 121 Auger Brake Yes Attachment Clutch Yes Drive Disc-O-Matic Speeds 6 Forward and 2 Reverse Lock Out Differential Pin-Lock Remote Wheel Lock Remote Wheel Lock Remote Differential Remote Differential Remote Wheel Lock Pneumatic Tires - in. (cm) 15/5 x 6 (38.1/12.7 x 15.2) 15/5 x 6 (38.1/12.7 x 15.2) 16/6.5 x 8 (40.6/16.5 x 20.3) 16/6.5 x 8 (40.6/16.5 x 20.3) 16/6.5 x 8 (40.6/16.5 x 20.3) 16/6.5 x 8 (40.6/16.5 x 20.3) Size and Weight Length - in. (cm) 61.5 (

3. Connect spark plug wire. GB - 17 Sharpen the Mower Blades CAUTION: DO NOT sharpen mower blades while on unit. An imbalanced mower blade will cause excessive vibration and eventual damage to unit. Check mower blade balance before reinstalling blades. NEVER weld or straighten bent blades. 1. Remove mower blade from unit. Discard mower blade if: • More than 1/2 in. (1.27 cm) of metal is removed. • Air lifts become eroded. • Blade is bent or broken. 2. Sharpen mower blade by removing an equal amo

4. To adjust deflector higher: Slide cable up. Tighten top nut. 5. Check travel and repeat adjustment as necessary. DISCHARGE CHUTE If chute does not stay in position while operating, tighten nut on carriage bolt at pivot point to increase tension on spring (Figure 14). GB - 22 Smooth and easy rotation of properly lubricated chute with crank is obtained by adjusting pinion and chute gear teeth so they mesh together. Figure 14 1. Pinion 2. Chute Gear 3. Carriage Bolt 4. Spring DS0113 1 2 3 4 Smoo

DO NOT throw snow any higher than necessary. Deflected materials can cause injury and property damage. Always stand clear of the discharge area when operating this unit. Fumes from engine exhaust can cause injury or death. DO NOT run engine in an enclosed area. Always provide good ventilation. ALWAYS disengage attachment, stop unit and engine, remove key and allow moving parts to stop before leaving operator’s position. ROTATING IMPELLER CAN CAUSE SERIOUS INJURY. NEVER ATTEMPT TO UNCLOG OR CLEAN

Pin on overtravel arm makes slight contact with end of slot. 4 STORAGE STORAGE WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. SHORT TERM IMPORTANT: NEVER spray unit with high pressure water or store unit outdoors. Run with attachment clutch engaged a few minutes after each use to free unit of any loose or melting snow. Close fuel shut-off valve. Inspect unit for visible signs of wear, breakage or damage. Keep all nuts, bolts and screws properly tightened

Place unit in the Belt Service Position. 1. Remove three nuts holding pulley to hub and remove pulley and key. 2. Loosen set screw in hub and remove hub. 3. Remove three nuts holding bearing flange to housing and remove bearing flange (Figure 19). 4. Remove two cap screws and lock washers on each side of blower housing holding rake shaft in position and remove bushing. 5. Remove three lock nuts attaching bearing support to housing and remove bearing support. 6. Grasp auger assembly and pull gear