BD920N-CS09......... .........Rivet............................................... ..................2x5................ ...........2 10 ... 5020......................... .........Graduated Ring.............................. ...........1 11... ... BD920N-CS11......... .........Key................................................. ..................3x13.............. ............1 12... ...5023......................... .........Spring............................................. ............1

5-6 6-7 Nomenclature and Use """'..". 7 Adjusting Tool Rest Operation Parts Breakdown ... ... ... 7 8-11 12 Parts List 13-14 Electrical Schematic ...... .15 3 Uncrating and Clean-Up Note: Uncrating and assembly will require two people due to the machines size and weight. 1. Finish removing contents from the shipping crate. Be sure to check crate thoroughly for any parts not found on initial unpacking. 2. Inspect contents for shipping damage and report any damage to your distributor. 3. Clean all

8 Installing Pen Mandrel Screw the mandrel (A, Fig. 10) into the threads in the headstock spindle and place the other end on the tip of the live center of the tailstock as shown. The barrel(s) of a pen can be placed between bushings, and held snug on the mandrel by the knurled nut (B, Fig. 10). If you are new to the practice of pen turning, a book entitled “Pens from the Wood Lathe” (stock # 709123) will demonstrate techniques and tips on turning, and is available from WMH Tool Group. Complete s

If in doubt, use the next heavier gauge. Remember, the smaller the gauge number, the heavier the cord. Volts Total Length of Cord in Feet 120V 25 50 100 150 AWG 12-16 Amps 14 12 Not Recommended 5 230 Volt Operation If 230V, single-phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This lathe is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 2

1 29........ JWL1642-129 ...............Plate...................................................... ............................................... 1 ........JWL1642-130...............Digital Readout......................................JWL-1642EVS........................1 ............JWL1642-130A.............Digital Readout......................................JWL-1642EVS-2.....................1 31........ TS-1540011..................Nut ........................................................

3. Move the point of skew to the right half of the desired width of your cut, see Figure 19. 4. With the bevel parallel to the right side of the cut, raise the handle and push the tool in to the desired depth. 5. Repeat from the left side. The two cuts should meet at the bottom and leave a clean "V" cut. 6. Additional cuts may be taken to add to either the depth or width of the cut. Parting 1. Place the parting tool on the tool rest and raise the handle until it starts to cut and continue to cut

To order parts or reach our service department, call 1-800-274-6848 between 7:30 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Figure 13 12 JML-1014I Mini Lathe 13 Parts List for JML-1014I Mini Lathe Index No. Part No. Description Size Qty 1............. JML1014-101 .... .....Headstock................................................. ..... 1 2..........

M-708376 Ph.: 800-274-6848 Revision A 9/06 Copyright © WMH Tool Group WARRANTY AND SERVICE WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. Fo

Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Lathe is assembled and running properly. Compare the contents of your container with the following parts list to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions. Contents of the Shipping Container 1 Lathe 1 Steady Rest (mounted on Lathe) 1 Fo

9 3. Apron -oil must be up to indicator mark in oil sight glass (A, Fig. 6). Top off with Mobil DTE. Oil Heavy Medium. Remove oil cap (B, Fig. 6) on top of apron to fill. To drain, remove drain plug on bottom of apron. Drain oil completely and refill after the first month of operation. Then, change oil in the apron annually. 4. Leadscrew Feed Rod -lubricate ball oiler (A, Fig. 7) on leadscrew/feed rod bracket with Mobil DTE. Oil Heavy Medium once daily. 5. Tailstock -lubricate two ball oilers (B