Votos - 2, Puntuación media: 4 ( )

Fabricar: Beko Tamaño del archivo: 670.15 kb Nombre del archivo: Idioma del manual:

End of Program The “Program Finished” lamp on the program follow-up indicator will light up when the program comes to an end. The lid is unlocked 2 minutes later, the “Program Finished” and “Lid” lamps will light up continuously. The machine is now ready for a second cycle. If any key is pressed when the machine is at the end of the program or if the position of the selection knob is changed, the “Program Finished” light will go off and only the “Lid” lamp will remain as lit. Meanwhile, if the door is still locked, the “Lid” light will continue flashing until the door is opened. Press the “On/Off” button to shut down the machine. 6 Quick instructions for daily use Preparation 1. Turn the tap on completely. Check if the hoses are connected tightly. 2. Place the laundry in the machine. 3. Add detergent and softener. Starting 1. Press the “On/Off” button. 2. Select the programme and the temperature. 3. If required (according to your machine’s model): – select any auxiliary function, – adjust the spin speed, – set the time delay, 4. Close the loading door. 5. Press Start/Pause/Cancel button. Canceling a program • Press “Start/Pause/Cancel” button for 3 seconds. The machine starts to discharge the water. “Wash” and “Program Finished” lights will light up. • "Start/Pause/Cancel" and “Wash” lights will go off after discharging process is over and the “Lid” light will start flashing. • If the program is cancelled in the middle of the process, “Wash” and “Program Finished” lights will light up. The machine can drain all the water or can take in water for 3 times at most to cool down the clothes and complete draining process. When water discharging process is completed, “Wash” light will go off, “Program Finished” light will light up and the “Lid” light will continuously flash until the door is allowed to be opened. You can make a new program selection when the “Lid” light is lit continuously. Adding more laundry You may add more laundry into the machine at the beginning of washing. C Machine allows adding more laundry during a later step only if the water level is low enough to open the loading door or if the temperature in the machine is low enough. In order to add laundry after the start-up of the program: 1. Press Start/Pause/Cancel button. Wait until the door is allowed to open. “Lid” lamp will light up continuously when the door is allowed to open. 2. Open the loading door and put in more laundry. 3. Close the loading door. 4. Press Start/Pause/Cancel button. Program is in rinse hold mode C After the machine fills with water in the final rinse step, clothes can be soaked in the machine as long as desired. When it reaches this position while the machine is running, the “Start/Pause/ Cancel” light will flash. In the machines equipped with spin speed selection knob, you can spin by selecting the desired spin speed and press "Start/Pause/Cancel" button. As for machines not equipped with a spin speed selection knob, you can end the program without spinning by pressing the “Start/Pause/Cancel” button to drain the water. You may spin your clothes whenever you wish to by selecting the spin program. Re-spinning the laundry The control system for an unbalanced load can pause the spinning in cases when the distribution of the laundry in the drum is not balanced. If you want to re-spin the clothes: 1. Rearrange the previously placed clothes in machine. 2. Select Spin+Pump program. 3. Set the spin speed if spin speed adjustment is available on your machine. 4. Press “Start/Pause/Cancel” button. After the program is finished 1. “Program finished” lamp will light up on the program follow-up indicator. The lid can be opened after 2 minutes when the “Program Finished” and “Lid” lamps light up continuously. 2. Press the On/Off button to shut down the machine. 3. Turn the water tap off. 4. Eliminate any folding of the rubber seal on the loading door and check for impurities. 5. Leave the loading door and detergent drawer open to dry. 7 Cleaning and care Detergent drawer Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. C If more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned. 2. Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching the residues in the drawer when cleaning. 3. Replace the drawer into its housing after cleaning. Check if the siphon is in its original location. The loading door and the drum After each wash: • Check if there are any foreign substances in the drum. • Open the hole in the bellow with the aid of a toothpick if it is clogged. C Foreign metal substances in your machine can cause rust stains. In such cases: Clean the drum with a stainless steel cleaning agent. Never use steel wool o...

Descargar ahora

Introduzca dos números de la imagen: