Votos - , Puntuación media:
(
)
)
Fabricar: Smeg
Tamaño del archivo: 586.26 kb
Nombre del archivo: AS62C-GB.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Warning indicators C Warning indicators may differ according to the model of your machine. Filter cleaning A warning LED will light up to remind filter cleaning after the program finishes. C If the filter cleaning warning LED lights up continuously, please refer to, “Solution suggestions for problems”. Water tank A warning LED will light up at the end of the program or when the tank is full with water. The machine stops operating when this warning LED lights up during a program running. To restart the machine, please drain the water in the water tank. Press “Start/Pause/Cancel” button to start the program after you have emptied the water tank. The warning LED goes off and the program resumes operating. Starting the Program 1. Press “Start/Pause/Cancel” button to start the program. 2. “Start/Pause/Cancel” button will light up to indicate that the program has started. Timer follow-up indicator One of the lamps is on as far as program runs and shows the approximate remaining time. C LEDs on the timer follow-up indicator will also flash when the child-proof lock is activated. C If more than one LED light up or flash concurrently, it means there is malfunctioning or a failure (please see, Solution suggestions for problems). Changing the program after the program has started You can use this feature to dry your laundry in a different program after your machine has started to run. For example; Press and hold the “Start/Pause/Cancel” button for about 3 seconds to select “80” minutes program instead of “60” minutes program. Select the “80” minutes program by rotating the program knob. Press “Start/Pause/Cancel” button to start the program. C The program which is selected first will go on even if the program selection button is moved and another program mode is selected while the machine is operating. You must cancel the ongoing program in order to change the drying program. (See, Ending the program through canceling) Adding/removing laundry in standby mode In order to add or take out laundry after the start-up of the program; 1. Press the “Start/Pause/Cancel” button to switch the machine to “Pause” mode. Drying process will stop. 2. Open the door at Pause position and close it again after adding or taking out laundry. 3. Press “Start/Pause/Cancel” button to start the program. C Any laundry added after the drying process was started may cause the already dried clothes in the machine intermingle with wet clothes and the result will be wet laundry after the drying process is over. C Laundry may be added or taken out as much as desired during a drying process, but as this process will interrupt drying continuously, it will extend the program duration and increase energy consumption. Therefore, it is recommended to add laundry before the drying program is started. Child-proof lock There is a childproof lock to prevent any program interruption due to the pressing of keys while the program is on. The loading door and all keys except the “On/Off” key on the panel are deactivated when the child- proof lock is active. In order to activate the childproof lock, press on the “Start/Pause/Cancel” and “Low temperature” buttons simultaneously for 3 seconds. To start a new program after the program is over or to interrupt the program, the childproof lock should be deactivated. To deactivate the childproof lock, press the same buttons for 3 sec. C One of the LEDs on the program follow-up indicator starts flashing when the child-proof lock is activated. Ending the program through canceling The program which is selected first will keep on going even if the position of the program selection button is changed. A new program can be selected and started after “Program cancel” is activated in order to change the drying program. To cancel any selected program; • Press “Start/Pause/Cancel” button for about a duration of 3 seconds. The “Filter cleaning” and “Water tank” warning LEDs as well as the “0” warning LED on the program follow-up indicator will light up at the end of this period for reminding purposes. A As the inside of the machine will be excessively hot when you cancel the program while the machine is running, activate the ventilation program to cool it down. End of program The “Filter cleaning” and “Water tank” warning LEDs as well as the “0” warning LED on the program follow-up indicator will light up at the end of the program. The door can be opened and the machine becomes ready for a second cycle. Press the “On/Off” button to shut down the machine. C A 2-hour anti creasing program to prevent laundry from creasing will be activated if you do not take the laundry out after the program has come to an end. C Clean the filter after each drying (please see, Filter cleaning). C Drain the water tank after each drying (please see, Water tank) Technical Specifications Models Condenser Dryer with time control Height / Height for built-under installation (cm) 85.0 / 82.0 Width (cm) 59.5 Depth / Depth for built-under installation (cm) 54 Hei...