Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
-- E-mail us at MDEAservice@mdea.com. -- Call Consumer Relations at 800-332-2119. • For information on System Reset, please see the back cover. • To order replacement or additional remote controls, lamp cartridges, or Owner’s Guides, visit our website at or call 800-553-7278. • Guidelines for setting up and using your new widescreen TV start on page 11. 26 TV Operation and Features 4 TV Operation and Features 4 Choosing a Viewing Source Input Selection menu Choose a viewing source from the Input Selection menu. The current TV input appears as a full-color icon in this menu. 1. Press INPUT to display the Input Selection menu. If there are only two inputs to the TV, INPUT switches between them without displaying the menu. 2. Highlight an input icon using . 3. Press ENTER to switch to the input and close the menu. More About the Input Selection Menu • To assign meaningful names to the icons, see the Inputs > Name menu, page 48. • To rearrange the icons, see the Inputs > Order menu, page 48. Sleep Timer The Sleep Timer turns the TV off after the length of time you set. To set the TV to turn on at a certain time, see the Setup > Timer menu on page 46. Setting the Sleep Timer 1. Press SLEEP on the remote control. 2. Press SLEEP additional times to increase the time in 30-minute increments up to the maximum of 120 minutes. 3. Press EXIT or wait five seconds without pressing any keys for the message to disappear. 4. Press SLEEP to view the time remaining before the sleep timer turns off the TV. Cancelling the Sleep Timer 1. Press SLEEP to display the on-screen message. 2. Press SLEEP repeatedly until OFF is displayed. Note: After five seconds of inactivity, the message box will disappear. TV Tips Turning the TV On or Off To turn the TV on or off, point the remote control at the front of the TV and press the POWER button. Alternatively, press the POWER button on the control panel of the TV. If You Turn Off the TV by Mistake Press 1. POWER again within about 60 seconds (while the lamp is still hot) to have the TV come back on immediately. If the 2. LAMP indicator starts blinking (about 60 seconds after you shut off power), wait a few moments for the LAMP indicator to stop blinking and press POWER to turn the TV on again. Controlling Sound Volume Press • VOL / to adjust the sound level. See also “Controlling A/V Receiver Sound Volume” on • page 15. Changing Channels (antenna sources) To change channels: Enter the channel number using the number keys • on the remote control and press ENTER. For a two- part digital channel, such as 3-1, press 3 — CANCEL 1 to enter a dash (separator). Press • CH/PAGE / to change channels one channel at a time. Press and hold • CH/PAGE / to move quickly through channels. Press • QV (QuickView) to switch back to the previously tuned channel. Press • GUIDE to display ChannelView channel listings, highlight a channel, and press ENTER to select. Use the Fav (Favorites) feature to set up lists of • favorite channels and tune to them with the FAV key. See Setup > Edit > Fav 1–Fav 6 on page 44. NOTE: Perform channel memorization to make finding channels easier. See Setup > Scan, page 43. 23 29 11 2 3 4 5 2524 27 28 26 17 18 1 23 29 11 2 3 4 5 2524 27 28 26 17 18 1 4. TV Operation and Features Remote Control 1. POWER: Turns TV power on and off. 2. Slide Switch: Selects the A/V device to be operated by the remote control. Set the slide switch to TV for operation of the TV, and NetCommandcontrolled devices. Control of additional devices requires programing (see Appendix C, “Programming the Remote Control.” 3. SLEEP: Sets the TV to turn off within 2 hours in increments of 30 minutes. 4. Digits/Letters: Press digits for channel numbers, then press ENTER for faster tuning. Use numbers and the — CANCEL key to enter digital sub-channel numbers. Use also for entering letters or names in menus. To select letters when naming channels, repeatedly press the associated number key. Press ENTER to set the letter. Special characters are available with the 1 key (!, &, blank space) and 0 key (/, *, -). 5. —/CANCEL (SUB-CHANNEL/CANCEL): When entering digital channel numbers, adds a separator between main and sub-channel numbers. Clears Fav and some menu entries. 6. QV (QuickView™): Switches between the current channel and the last channel viewed. 7. MUTE: Turns TV sound on and off. 8. SPLIT: Not used in this model. 9. FAV (Favorites): Scans through memorized lists of favorite channels. See Setup > Edit > Fav1–Fav6 on page 44. 10. VOL / (Volume Up/Down): Changes sound level. 11. CH/PAGE / (Channel or Page Up/Down): Scans up or down through memorized channels. Pages up and down through screens when used with ChannelView™. 12. FORMAT: Changes the shape and size of the TV picture. 13. LIST (835 Series): Works like the LIST key for a cable box or satellite receiver when “learned” for NetCommand or when the remote has been programmed for the device. 14. INPUT: Displays the Input Selection menu from wh...