Votos - 2, Puntuación media: 4 ( )

Fabricar: Mitsubishi Electronics Tamaño del archivo: 3.92 mb Nombre del archivo: ece57210-de50-e024-95f7-a18425987362.pdf Idioma del manual:

The device should perform the selected function. The device needs to be turned on and the IR emitters properly placed for the test to be successful (see page 22 for IR emitter placement). 5. Repeat for each function to be learned. 6. To erase a learned function, highlight the check box for that function and press CANCEL. 7. When the function signals have been learned, press ADJUST to select Next> and move to the [Device] Advanced Learn screen. NOTE: When learning the device’s remote control signals, point the device’s remote control at the TV screen. Hint: If the device’s remote control uses a single button for both Power On and Power Off, don’t learn the Power Off function. [Device] Advanced Learn Screen Figure 17 After learning the basic device keys, the [Device] Advanced Learn screen allows you to learn any special keys for your device. Most common IR remote control signal formats can be learned by NetCommand. A table of specialized device keys is shown in Appendix E. You only need to learn the functions your devices respond to and can ignore the functions that do not apply to your device. Figure 17 [Device] Advanced Learn screen Name Screen Figure 18 The Name screen allows you to change the default name for each device to a custom name of up to eight characters (including a blank space), selecting from letters, numbers and nine different characters. Press ADJUST or to select each letter, then press ENTER to move to the next position. Press CANCEL on the remote to delete the current letter and move back one character position. When in the first position, the CANCEL button will return the name to the default name. Figure 16. [Device] Learn screen Figure 18. Name screen Edit NetCommand®, Adding Devices, continued The screens described below may not be necessary for your device setup. If it does not display automatically on- screen, it is not required. Connection for [Device] Screen Figure 19 This screen allows the TV to learn the connection between device(s) and input(s). Inputs 1-3, Components 1 & 2, and/or the inputs for the A/V Receiver all need to be checked, if connected. Add or remove check marks to indicate what type of connections (Audio, Video or Both) are used with each TV and A/V Receiver input. Note: Video inputs to the A/V Receiver are normally used to transfer signals to the line input of a VCR for recording. Mitsubishi recommends leaving Video unchecked. RF Connection for Cable Screen Figure 21 The RF Connection screen displays only when adding or changing a cable box. If your cable box is connected to a TV Antenna input, check the RF checkbox. Select the TV antenna input that is used with the cable box Select the channel number used for output by your cable box. The default channel is 003. If the cable box is also connected to a VCR for recording, select that VCR. If your cable box is connected using Audio/Video cables, make sure the RF checkbox is unchecked. Then the next screen will be Connection (Figure 19), to allow the selection of the TV input used with the cable box. Figure 19. Connection for [Device] screen Figure 21. RF Connection for Cable screen IR Code for [Device] Screen Figure 22 This screen only displays if an added device has the same IR code as a previously added device of the same type and manufacturer. You can specify the IR setting for the new device. For example, for the second Mitsubishi VCR you can specify the IR Code setting to VCR-B, if the primary Mitsubishi VCR is using the VCR- A IR code. VCR for Recordings Screen Figure 20 Select the VCR you would like to use for recording. You may also select whether you want the recorded 16:9 signals from digital channels or IEEE-1394 devices to be cropped (sides are cut off) or Anamorphic (full screen). If Anamorphic is selected for viewing, choose the Standard format for the best quality playback. Figure 20. VCR for Recordings screen Figure 22. IR Code for [Device] screen Edit NetCommand®, Changing, Deleting Devices, Finish Screen Change Screen Figure 23 Selecting Change from the Setup menu screen, displays the Change screen. To change a device, select the device by name, not type. You can change the name or input connections to the TV and A/V Receiver. If “Other” is selected for the manufacturer then you can also “Learn”. The rest of the screens that follow are the same as when you Add a device. Finish Screen Figure 25 To finalize your selections and complete the NetCommand setup, select Finish from the Finish screen. Note: To change any of the inputs or names for the devices, or add devices not included in the initial settings, select Edit to display the Edit NetCommand menu. Figure 23. Change screen Figure 25. Finish screen Delete Screen Figure 24 Selecting Delete from the Setup menu displays the Delete screen. You can choose to delete a single device by selecting the device you would like to delete, or you can delete the entire NetCommand configuration. After you have chosen the device, or the entire configuration, you w...

Descargar ahora

Introduzca dos números de la imagen: