Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Note: Choose 3D mode manually when autodetection is not available. 3D signalnotification Off/ On On: Displays a message according to thesignal received by the Auto detect 3D . 2D 3Ddepth Minimum/ Medium / Maximum Adjusts 3D depth. Available only when 2D3D is selected in 3D format select . Available only when 3D content is displayed. Watching TV 3D 3D settings (2) MENU Menu > Setup > 3D settings Settings Options Description 3D adjustment Off /On Changes 3D depth by adjusting left-rightparallax. Set to On to adjust Effect ( -3 to +3 ). Left/Right swap Normal / Swapped Change this to Swapped when the phasesare reversed (When there is an unusual sense ofdepth). Diagonal linefilter Off /On On: Resolves discomfort caused by receiving aquincunx matrix signal. Safetyprecautions Displays message for viewing 3D images. Watching TV Computer on TV Display PC screen 1.Connect PC Connect the PC's video output to the PC terminal of this TV with PC cable. To listen to the PC sound, connect an audio cable between the computer and theTV. 2.Select Input and display 1. Display Input select menu (With the connected equipment turned On) INPUT 2. Select the PC input Select PC input using / and press 3. Display PC screen Watching TV Computer on TV PC adjustments (1) MENU Menu > Picture > PC adjustments Settings Options Description Reset todefaults Resets all PC adjustments to factory defaultsettings. Sync H & V The H and V sync signals are input from theHD/VD connector. On green Uses a synchronized signal on the Video Gsignal, which is input from the G connector. Dot clock Alleviates the problem if a picture appears tobe vertically-striped, flickers partially or is blurred. H-position Adjusts the horizontal position using left/rightcursor button. V-position Adjusts the vertical position using left/rightcursor button. Watching TV Computer on TV PC adjustments (2) MENU Menu > Picture > PC adjustments Settings Options Description Clock phase Alleviates the problem if the whole pictureappears to flicker or is blurred. First adjust the DotClock to get the best possible picture, then adjustthe Clock phase so that a clear picture appears. It may not be possible to display a clear picturedue to poor input signals. Input resolution Switches to wide display and selects theappropriate screen resolution. VGA (640 x 480 pixels), WVGA (852 x 480pixels), XGA (1,024 x 768 pixels), WXGA (1,280 x768 pixels) Options change depending on signals. H-frequency V-frequency Displays the H (Horizontal)/V (Vertical) frequencies. Display range Horizontal: 15 - 110 kHz Vertical: 48 - 120 Hz Watching TV Computer on TV Input signal Signals other than below may not be displayed properly. The signals are reformatted for optimal viewing on your display. Computer signals which can be input are those with a horizontal scanningfrequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) Input signal Horizontal frequency (kHz) Vertical frequency (Hz) 640 x 480 @60 31.47 59.94 852 x 480 @60 31.44 59.89 800 x 600 @60 37.88 60.32 1,024 x 768 @60 48.36 60.00 1,280 x 768 @60 47.78 59.87 1,280 x 1,024 @60 63.98 60.02 1,366 x 768 @60 48.39 60.04 Internet services "VIERA Connect" Connect to network Network connections (1) 1.Contact your Broadband service provider If you don't have Internet service from your local provider, please order a high- speed Internet service at no less than the connection speed below. If you alreadyhave this service, make sure that the connection speed exceeds the following: Required speed (effective): at least 1.5 Mbps for SD and 6 Mbps for HD picturequality, respectively. Dial-up Internet service cannot be used for VIERA Connect. 2.Select wired or wireless connection If the Cable/DSL modem is close to the TV and you have only one TV set, you maychoose a wired connection. If the Cable/DSL modem is far from the TV and/or you have more TVs in thehouse, you may want to use a wireless network. Internet services "VIERA Connect" Connect to network Network connections (2) 3.Connecting to the Internet A. Wireless connection If you are using the network for connecting various pieces of equipment and wantto connect the TV, you could also use a Wireless LAN and Access point to connectthe TV to the Internet. TV(Built-in Wireless LAN) Access point - Hub, Router- Modem- DLNA Certified media server(for example, PC, etc.) *To use only DLNA features, you can operate the features without Broadbandnetwork environment. You can just connect the TV directly to the equipment with a LAN cross cable. Internet services "VIERA Connect" Connect to network Network connections (3) B. Wired connection (Directly connected) If you are not using the network for connecting anything else but the TV, you canjust connect the TV directly to the Cable/DSL Ethernet modem with LAN cable. TV ETHERNET LAN cable Modem Internet services "VIERA Connect" Connect to network Network connections (4) ...