Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Panasonic Tamaño del archivo: 4.71 mb Nombre del archivo: Idioma del manual:

Optional Terminal Board Insert Slot (covered) Connections PC Input Terminals connection COMPUTER AUDIO TH-42PWD8 Conversion adapter (if necessary) RGB PC cable Stereo plugAudio Connect a cable which matches the audio output terminal on the computer. Mini D-sub 15p Notes: • Due to space limitations, occasionally you may have trouble connecting Mini D-sub 15P cable with ferrite core to PC input Terminal. • Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) • The display resolution is a maximum of 640 . 480 dots (TH-37PWD8GK/S, TH-42PWD8GK/S), 768 . 720 dots (TH37PHD8GK/ S), 768 . 768 dots (TH-42PHD8GK/S) when the aspect mode is set to “NORMAL”, and 852 . 480 dots (TH-37PWD8GK/S, TH-42PWD8GK/S), 1,024 . 720 dots (TH-37PHD8GK/S), 1,024 . 768 dots (TH-42PHD8GK/S) when the aspect mode is set to “FULL”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with suffi cient clarity. • The PC input terminals are DDC1/2B-compatible. If the computer being connected is not DDC1/2B-compatible, you will need to make setting changes to the computer at the time of connection. • Some PC models cannot be connected to the set. • There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. • The computer shown in the illustration is for example purposes only. • Additional equipment and cables shown are not supplied with this set. • Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. • Component Input is possible with the pin 1, 2, 3 of the D-sub 15P Connector. Signal Names for Mini D-sub 15P Connector 1 678 3 9 45 10 1514131211 2 Pin Layout for PC Input Terminal Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 R (PR/CR) 6 GND (Ground) 11 GND (Ground) 2 G (Y) 7 GND (Ground) 12 SDA 3 B (PB/CB) 8 GND (Ground) 13 HD/SYNC 4 GND (Ground) 9 NC (not connected) 14 VD 5 GND (Ground) 10 GND (Ground) 15 SCL Connections SERIAL Terminals connection The SERIAL terminal is used when the Plasma Display is controlled by a computer. 9876 5321 4 SERIAL Pin layout for RS-232C COMPUTER RS-232C Straight cable D-sub 9p Notes: • Use the RS-232C cable to connect the computer to the Plasma Display. • The computer shown is for example purposes only. • Additional equipment and cables shown are not supplied with this set. The SERIAL terminal conforms to the RS-232C interface specification, so that the Plasma Display can be controlled by a computer which is connected to this terminal. The computer will require software which allows the sending and receiving of control data which satisfies the conditions given below. Use a computer application such as programming language software. Refer to the documentation for the computer application for details. Communication parameters Signal level RS-232C compliant Synchronization method Asynchronous Baud rate 9600 bps Parity None Character length 8 bits Stop bit 1 bit Flow control - RS-232C Conversion cable D-sub 9-pin female Details 2 R X D 3 T X D 5 GND 4 6• Non use 7 8 Shorted 91 • NC Basic format for control data Command The transmission of control data from the computer starts with a STX signal, followed by the command, the parameters, and lastly an ETX signal in that order. If there are no parameters, then the parameter signal does not need to be sent. End (03h) (02h) command (3 bytes) Notes: • If multiple commands are transmitted, be sure to wait for the response for the first command to come from this unit before sending the next command. • If an incorrect command is sent by mistake, this unit will Command Parameter Control details PON None Power ON POF None Power OFF AVL ** Volume 00 - 63 AMT 0 Audio MUTE OFF 1 Audio MUTE ON IMS None SL1 SL2 SL3 PC1 Input select (toggle) Slot1 input Slot2 input Slot3 input PC input DAM None NORM ZOOM FULL JUST SELF Screen mode select (togg...

Descargar ahora

Introduzca dos números de la imagen: