Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Be sure to disconnect all cables before moving the Plasma Display. • Moving the Display with its cables attached might damage the cables which, in turn, can cause fire or electric shock. Disconnect the power plug from the wall outlet as asafety precaution before carrying out any cleaning. • Electric shocks can result if this is not done. Clean the power cable regularly to prevent it frombecoming dusty. • Built-up dust on the power cord plug can increase humidity which might damage the insulation and cause fi re. Unplug the cord from the wall outlet and clean it with a dry cloth. This Plasma Display radiates infrared rays, therefore itmay affect other infrared communication equipment. Install your infrared sensor in a place away from direct or reflected light from your Plasma Display. Note: Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention to remain on the Plasma Display. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. Safety Precautions / Maintenance WARNING Setup Do not place the Plasma Display on sloped or unstablesurfaces. • The Plasma Display may fall off or tip over. Do not place any objects on top of the Plasma Display. • If water spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in fi re or electric shock. If any foreign objects get inside the Plasma Display, please consult an Authorized Service Center. Do not cover the ventilation holes. • Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display. Transport only in upright position! • Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry. If using the pedestal (optional accessory), leave a spaceof 3 15/16” (10 cm) or more at the top, left and right, and2 3/4” (7 cm) or more at the rear, and also keep the spacebetween the bottom of the display and the fl oor surface. If using some other setting-up method, follow the manualof it. (If there is no specific indication of installation dimension in the installation manual, leave a space of3 15/16” (10 cm) or more at the top, bottom, left and right, and 2 3/4” (7 cm) or more at the rear.) An apparatus with CLASS I construction shall beconnected to a mains socket outlet with a protectiveearthing connection. AC Power Supply Cord The Plasma Display is designed to operate on 110 - 127 V AC, 50/60 Hz. Do not use any power supply cord other than thatprovided with this unit. • Doing so may cause fire or electric shocks. Maintenance Securely insert the power cord plug as far as it will go. • If the plug is not fully inserted, heat may be generated which could cause fire. If the plug is damaged or the wall socket plate is loose, they should not be used. Do not handle the power cord plug with wet hands. • Doing so may cause electric shocks. Do not do anything that might damage the power cable. When disconnecting the power cable, hold the plug, not the cable. • Do not make any modifications, place heavy objects on, place near hot objects, heat, bend, twist or forcefully pull the power cable. Doing so may cause damage to the power cable which can cause fire or electric shock. If damage to the cable is suspected, have it repaired at an Authorized Service Center. If the Plasma Display will not be used for a long periodof time, unplug the power cord from the wall outlet. If problems occur during use If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odor is detected from the Plasma Display, unplug the power cord immediately. • Continuous use of the Display under these conditions might cause fire or permanent damage to the unit. Have the Display evaluated at an Authorized Service Center. Services to the Display by any unauthorized personnel are strongly discouraged due to its high voltage dangerous nature. If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinetbecomes damaged, disconnect the power cord plugimmediately. • A short may occur, which could cause fire. Contact an Authorized Service Center for any repairs that need to be made. The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning cloth or a soft, lint-free cloth. • If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surface is dry. • Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the surface may be adversely affected. If the cabinet becomes dirty...
Otros modelos de este manual:TV - TH-50PH12U (1.95 mb)
TV - TH-42PH12L (1.95 mb)
TV - TH-50PH12L (1.95 mb)