44040-01 • 03/24/201018 ©2010 Hunter Fan Company 19 5 Temporary Schedule Change Scheduling Home Menu Schedule setting temporary temperature hold Cool to 73o1 Done Home Menu Schedule setting temporary temperature hold Cool to 73o2 Done Home MenuSchedule temporary hold[resume] to run schedule Cool to 73o74o Auto3 Energy Savings: GoodBest! At homeResume ©2010 Hunter Fan Company 19 5 Temporary Schedule Change Scheduling Home Menu Schedule setting temporary temperature hold Cool to 73o1 Done Home Men

Aumentando el punto de ajuste de su termostato en 5°F (3°C) por dos periodos de 8 horas durante el verano puede reducir su factura de combustible hasta en 25%. Y Su termostato puede contener hasta 4 programas separados para cada dia de la semana. Usted puede programar los dias de semana, los fines de semana, los 7 dias individualmente o todos los dias como un grupo. El ventilador del sistema tambien puede fijarse para operar continuamente durante un periodo de tiempo programado. Su termostato Hu

1) Si su sistema es un horno a gas, coloque el interruptor en la posicion HE. 2) Si su sistema es un horno electrico, coloque your existing thermostat is marked... label the wire with this sticker: G / FGGW / H / BW/BW/BY / C* / M / OY/0Y/0RC / VCRCRCRH / R / VR / 4RHRH24 Volt24 Volt coolair conditioning compressorheatingfanY1Y1Y1heat pump compressor 3) Si su sistema es una bomba de calor de simple etapa, coloque el interruptor en la posicion SSHP. ¦ Introduzca las pestanas superiores del cuerpo

Sin embargo, no hay garantia de que no pueda producirse interferencia en una instalacion en particular. Si este equipo causa alguna interferencia perjudicial a la recepcion de radio o television, lo que puede determinarse apagando y encendiendo el equipo, el usuario debe tratar de corregir la interferencia aplicando una o mas de las medidas siguientes: • Aumente la separacion entre el equipo y el receptor. • Conecte el equipo en una salida de un circuito diferente del circuito en que esta conect

4. Using the provided stickers, label each wire according to the Wire Labels chart. (If the terminals are not labeled, contact a qualified HVAC technician.) Note: Wire colors do not always comply with standards, so wire color should be ignored. Refer to the existing terminal designation for proper identification. *If wires marked Y & C are both present, C may be a Common wire and should not be used. If you have a wire marked C, do not connect it to any terminal. This wire is used only for non-ba

See pages 50-51 for more information. 44 energyUsageTodayMinHr energyUsageTodayMinHr ICOnS AnD FEATUrES, COnT. 3. Energy – calculates energy usage. Press to display the total operation time for heat and air conditioning for today, yesterday, last week, or Total. Monitoring energy usage allows you to optimize energy savings. Press ENERGY to cycle through Today, Yesterday, This Week, and Total (up to 999 hours and 59 minutes). Press and hold ENERGY until the display blinks to reset the counter. no

Set & $aveSet & $aveSet & $ave Installation and Operation Manual Model 44360 Programmable Thermostat English Form# 42710-01 20091204 ©2009 Hunter Fan Co. Set & $aveSet & $aveSet & $ave Installation and Operation Manual Model 44360 Programmable Thermostat English 2 Table of Contents Important Information .............................................................................. 5 Tools ........................................................................................................ 6 U

See Figure 4. Ignore any wires which may be present, but which were not connected to the old thermostat. Terminal Screws Figure 4 • Be sure to tighten the terminal screws securely, as a loose wire could cause operational problems with your system or thermostat. • Push excess wire back into the hole to prevent interference when installing the thermostat to the wallplate. • Set the System Switch to “off”, and the Fan Switch to “auto”. • On the back of the thermostat are the System Set-Up Switches.

(The ends of any extra wires should be wrapped in electrical tape and carefully pushed back into the wall.) 3. Push any excess wire length back into the wall to prevent interference. GRCRHYWJumper 18 DISABLE ENABLE RECOVERY HG HE G SYSTEM TYPE STD HP W/B Y/O RH RC Y1 FAN OPTION AMHEATTThermostat Cover System Switch G RC RH Y/O W/B Y1 DISABLE ENABLE RECOVERY HG HE G SYSTEM TYPE STD HP W/B Y/O RH RC Y1 FAN OPTION AMHEATTThermostat Cover System Switch G RC RH Y/O W/B Y1 inSTalling ThE ThErMoSTaT, C

This thermostat will not control line voltage systems. You will need the following tools to complete your installation: • Phillips Screwdriver (#2) • Two 1.5V (AA) size alkaline batteries Take note of these warnings and cautions before proceeding: • Read all installation instructions before beginning installation! If you still need assistance after reading this manual, call our Technical Support at 1-888-830-1326. • Do not disconnect the wires from your old thermostat until all wires have been p