Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
See the inset drawing. Identify the Left Pedal (10), which is marked with an "L" sticker. Attach the Left Pedal to the Left Pedal Leg (4) with two M6 x 48mm Flat Head Screws (83). Note: The Left Pedal can be attached in any of three positions using the three sets of holes in the Left Pedal Leg. Attach the Right Pedal (not shown) to the Right Pedal Leg (not shown) in the same way. 6. Hold a Pedal Wheel (28) inside of the bracket on one of the Upper Body Legs (31). Hold the Upper Body Leg and the Pedal Wheel inside of the bracket on the Left Pedal Leg (4). Slide a Pedal Leg Cover (33) onto the long side of an M8 x 63mm Bolt Set (65), and insert the Bolt Set into the Left Pedal Leg, the Upper Body Leg, and the Pedal Wheel. Slide a Pedal Leg Cover (33) onto the short side of the M8 x 63mm Bolt Set (65) and tighten it into the long side of the Bolt Set. Attach the other Upper Body Leg (not shown) and the other Pedal Wheel (not shown) to the other side of the elliptical exerciser in the same way. Grease 34 113 66 111 10 i0 oi 33 65 28 7. ApplyasmallamountoftheincludedTeflon®lubricant toa papertowel.Ruba thinfilmofthelubricantonto eachUpperBodyLeg(31). IdentifytheLeftUpperBodyArm(112),whichis markedwithan"L"sticker.SlidetheLeftUpperBody ArmontotheleftUpperBodyLeg(31).SlidetheRight UpperBodyArm(118)ontotherightUpperBodyLeg (notshown).Make sure that the Upper Body Arms are on the correct sides. Next, slide an Axle Cover (26) onto the post on each Upper Body Arm. Apply grease to the Arm Axle (19). Insert the Arm Axle into the Upright (2), the right Axle Cover (26), and the Right Upper Body Arm (118). Next, push the Arm Axle into the Upright until the left end of the Arm Axle is flush with the left side of the Upright. Then, raise the Left Upper Body Arm (112), and insert the Arm Axle into the left Axle Cover (26) and the Left Upper Body Arm. Center the Arm Axle and rotate it so the indicated hole is in the position shown. 8. Have another person hold the Left Handlebar (24) near the Upright (2) as shown. Connect the left Pulse Sensor Wire (20) to the Pulse Extension Wire (101 ). Slide an Axle Cover Endcap (91) onto the lower end of the Left Handlebar. Slide the upper end of the Left Handlebar (24) into the tube on the front of the Upright (2), while sliding the lower end of the Left Handlebar onto the Arm Axle (19). Attach the upper end of the Left Handlebar with two M8 x 42mm Button Bolts (85) and two M8 Nylon Jam Nuts (86); be careful not to damage the Wires (20, 101) as you insert the Button Bolts. Make sure that the Jam Nuts are resting in the hexagonal holes in the tube on the front of the Upright. Attach the lower end of the Left Handlebar with an M8 x 35mm Button Bolt (105) and an M8 Jam Nut (86). Press the tabs on the Axle Cover Endcap (91) into the left Axle Cover (26). Attach the Right Handlebar (23) to the Upright (2) in the same way. Hold the halves of the Handlebar Cover (25) around the tube on the front of the Upright (2); be careful not to damage the Wires (20, 101}. Attach the Handlebar Cover with an M4 x 16mm Round Head Screw (96). // // \\ Hole \\ \ 26 24 91 9. HaveanotherpersonholdtheConsole(17)neartheUpright(2). ConnecttheUpperWireHarness(95)to thewirehar nessontheConsole(17).ConnectthePulse ExtensionWire(101) tothepulsewireontheConsole. Next,locatethetwogroundwiresthatareattachedto theUpright(2).Connectthegroundwirestothetwo smallestwireson theConsole. CarefullyinsertallexcesswiringupintotheConsole (17)anddownintotheUpright(2).AttachtheConsole totheUprightwithfourM4x 16mmScrews(98). (Note:TheScrewsmaybefoundintheconsolebox.) Be careful to avoid pinching the wires. 10. Plug the Power Cord (93) into the Power Socket (92) at the rear of the elliptical exerciser. 11. Make sure that all parts of the elliptical exerciser are 9 Do not pinch the wires during this step. 101 98 93 properly tightened. Cover the floor beneath the elliptical exerciser to protect the floor from damage. Note: Some extra hardware may be left after assembly is completed. HOW TO USE THE CHEST PULSE SENSOR To get the best performance from the chest pulse sensor, please read the instructions below. HOW TO PUT ON THE CHEST PULSE SENSOR The chest pulse sensor consists of two components: the chest strap and the sensor unit. Follow the steps below to put on the chest pulse sensor. _/Chest Strap _-_.. Tab _t Sensor Unit Sensor Buckle Unit _F_See the inset drawing above. Insert the tab on one end of the chest strap through one end of the sensor unit as shown. Then, press the end of the sensor unit under the buckle on the chest strap. B Wrap the chest pulse / sensor around your chest. Attach the free end of ) the chest strap to the sensor unit as described above. Adjust the length of the chest strap, if necessary. The chest pulse sensor should be under your clothing, against your skin, and as high under the pectoral muscles or breasts as is comfortable. Make sure that the logo is facing forward and is right-side-up. Pull the sensor unit Ele...